lkml.org 
[lkml]   [2020]   [Nov]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v5 4/8] media: i2c: max9286: Make channel amplitude programmable
Date
Instrument the function that configures the reverse channel with a
programmable amplitude value.

This change serves to prepare to adjust the reverse channel amplitude
depending on the remote end high-threshold configuration.

Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
---
drivers/media/i2c/max9286.c | 22 ++++++++++++++++------
1 file changed, 16 insertions(+), 6 deletions(-)

diff --git a/drivers/media/i2c/max9286.c b/drivers/media/i2c/max9286.c
index 526b6e557dfb..31e27d0f34f1 100644
--- a/drivers/media/i2c/max9286.c
+++ b/drivers/media/i2c/max9286.c
@@ -336,19 +336,29 @@ static void max9286_configure_i2c(struct max9286_priv *priv, bool localack)
usleep_range(3000, 5000);
}

-static void max9286_reverse_channel_setup(struct max9286_priv *priv)
+static void max9286_reverse_channel_setup(struct max9286_priv *priv,
+ unsigned int chan_amplitude)
{
+ /* Reverse channel transmission time: default to 1. */
+ u8 chan_config = MAX9286_REV_TRF(1);
+
/*
* Reverse channel setup.
*
* - Enable custom reverse channel configuration (through register 0x3f)
* and set the first pulse length to 35 clock cycles.
- * - Increase the reverse channel amplitude to 170mV to accommodate the
- * high threshold enabled by the serializer driver.
+ * - Adjust reverse channel amplitude: values > 130 are programmed
+ * using the additional +100mV REV_AMP_X boost flag
*/
max9286_write(priv, 0x3f, MAX9286_EN_REV_CFG | MAX9286_REV_FLEN(35));
- max9286_write(priv, 0x3b, MAX9286_REV_TRF(1) | MAX9286_REV_AMP(70) |
- MAX9286_REV_AMP_X);
+
+ if (chan_amplitude > 100) {
+ /* It is not possible to express values (100 < x < 130) */
+ chan_amplitude = chan_amplitude < 130
+ ? 30 : chan_amplitude - 100;
+ chan_config |= MAX9286_REV_AMP_X;
+ }
+ max9286_write(priv, 0x3b, chan_config | MAX9286_REV_AMP(chan_amplitude));
usleep_range(2000, 2500);
}

@@ -957,7 +967,7 @@ static int max9286_setup(struct max9286_priv *priv)
* only. This should be disabled after the mux is initialised.
*/
max9286_configure_i2c(priv, true);
- max9286_reverse_channel_setup(priv);
+ max9286_reverse_channel_setup(priv, 170);

/*
* Enable GMSL links, mask unused ones and autodetect link
--
2.29.1
\
 
 \ /
  Last update: 2020-11-16 14:55    [W:1.925 / U:1.052 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site