lkml.org 
[lkml]   [2020]   [Nov]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH net-next v2 07/11] net: dsa: microchip: ksz9477: add Posix clock support for chip PTP clock
On Thu, Nov 12, 2020 at 04:35:33PM +0100, Christian Eggers wrote:
> diff --git a/drivers/net/dsa/microchip/Kconfig b/drivers/net/dsa/microchip/Kconfig
> index 4ec6a47b7f72..71cc910e5941 100644
> --- a/drivers/net/dsa/microchip/Kconfig
> +++ b/drivers/net/dsa/microchip/Kconfig
> @@ -24,6 +24,15 @@ config NET_DSA_MICROCHIP_KSZ9477_SPI
> help
> Select to enable support for registering switches configured through SPI.
>
> +config NET_DSA_MICROCHIP_KSZ9477_PTP
> + bool "PTP support for Microchip KSZ9477 series"
> + default n

"default n" is implicit, please remove this

> + depends on NET_DSA_MICROCHIP_KSZ9477
> + depends on PTP_1588_CLOCK
> + help
> + Say Y to enable PTP hardware timestamping on Microchip KSZ switch
> + chips that support it.
> +
> menuconfig NET_DSA_MICROCHIP_KSZ8795
> tristate "Microchip KSZ8795 series switch support"
> depends on NET_DSA
> diff --git a/drivers/net/dsa/microchip/Makefile b/drivers/net/dsa/microchip/Makefile
> index c5cc1d5dea06..35c4356bad65 100644
> --- a/drivers/net/dsa/microchip/Makefile
> +++ b/drivers/net/dsa/microchip/Makefile
> @@ -2,6 +2,7 @@
> obj-$(CONFIG_NET_DSA_MICROCHIP_KSZ_COMMON) += ksz_common.o
> obj-$(CONFIG_NET_DSA_MICROCHIP_KSZ9477) += ksz9477.o
> ksz9477-objs := ksz9477_main.o
> +ksz9477-$(CONFIG_NET_DSA_MICROCHIP_KSZ9477_PTP) += ksz9477_ptp.o
> obj-$(CONFIG_NET_DSA_MICROCHIP_KSZ9477_I2C) += ksz9477_i2c.o
> obj-$(CONFIG_NET_DSA_MICROCHIP_KSZ9477_SPI) += ksz9477_spi.o
> obj-$(CONFIG_NET_DSA_MICROCHIP_KSZ8795) += ksz8795.o
> diff --git a/drivers/net/dsa/microchip/ksz9477_i2c.c b/drivers/net/dsa/microchip/ksz9477_i2c.c
> index 4ed1f503044a..315eb24c444d 100644
> --- a/drivers/net/dsa/microchip/ksz9477_i2c.c
> +++ b/drivers/net/dsa/microchip/ksz9477_i2c.c
> @@ -58,7 +58,7 @@ static int ksz9477_i2c_remove(struct i2c_client *i2c)
> {
> struct ksz_device *dev = i2c_get_clientdata(i2c);
>
> - ksz_switch_remove(dev);
> + ksz9477_switch_remove(dev);
>
> return 0;
> }
> diff --git a/drivers/net/dsa/microchip/ksz9477_main.c b/drivers/net/dsa/microchip/ksz9477_main.c
> index 6b5a981fb21f..7d623400139f 100644
> --- a/drivers/net/dsa/microchip/ksz9477_main.c
> +++ b/drivers/net/dsa/microchip/ksz9477_main.c
> @@ -18,6 +18,7 @@
>
> #include "ksz9477_reg.h"
> #include "ksz_common.h"
> +#include "ksz9477_ptp.h"
>
> /* Used with variable features to indicate capabilities. */
> #define GBIT_SUPPORT BIT(0)
> @@ -1719,10 +1720,26 @@ int ksz9477_switch_register(struct ksz_device *dev)
> phy_remove_link_mode(phydev,
> ETHTOOL_LINK_MODE_1000baseT_Full_BIT);
> }
> +
> + ret = ksz9477_ptp_init(dev);
> + if (ret)
> + goto error_switch_unregister;
> +
> + return 0;
> +
> +error_switch_unregister:
> + ksz_switch_remove(dev);
> return ret;
> }
> EXPORT_SYMBOL(ksz9477_switch_register);
>
> +void ksz9477_switch_remove(struct ksz_device *dev)
> +{
> + ksz9477_ptp_deinit(dev);
> + ksz_switch_remove(dev);
> +}
> +EXPORT_SYMBOL(ksz9477_switch_remove);
> +
> MODULE_AUTHOR("Woojung Huh <Woojung.Huh@microchip.com>");
> MODULE_DESCRIPTION("Microchip KSZ9477 Series Switch DSA Driver");
> MODULE_LICENSE("GPL");
> diff --git a/drivers/net/dsa/microchip/ksz9477_ptp.c b/drivers/net/dsa/microchip/ksz9477_ptp.c
> new file mode 100644
> index 000000000000..44d7bbdea518
> --- /dev/null
> +++ b/drivers/net/dsa/microchip/ksz9477_ptp.c
> @@ -0,0 +1,301 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/* Microchip KSZ9477 switch driver PTP routines
> + *
> + * Author: Christian Eggers <ceggers@arri.de>
> + *
> + * Copyright (c) 2020 ARRI Lighting
> + */
> +
> +#include <linux/ptp_clock_kernel.h>
> +
> +#include "ksz_common.h"
> +#include "ksz9477_reg.h"
> +
> +#include "ksz9477_ptp.h"
> +
> +#define KSZ_PTP_INC_NS 40 /* HW clock is incremented every 40 ns (by 40) */
> +#define KSZ_PTP_SUBNS_BITS 32 /* Number of bits in sub-nanoseconds counter */
> +
> +/* Posix clock support */
> +
> +static int ksz9477_ptp_adjfine(struct ptp_clock_info *ptp, long scaled_ppm)
> +{
> + struct ksz_device *dev = container_of(ptp, struct ksz_device, ptp_caps);
> + u16 data16;
> + int ret;
> +
> + if (scaled_ppm) {
> + /* basic calculation:
> + * s32 ppb = scaled_ppm_to_ppb(scaled_ppm);
> + * s64 adj = div_s64(((s64)ppb * KSZ_PTP_INC_NS) << KSZ_PTP_SUBNS_BITS,
> + * NSEC_PER_SEC);
> + */
> +
> + /* more precise calculation (avoids shifting out precision) */
> + s64 ppb, adj;
> + u32 data32;

Don't you want to move these declarations right beneath the "if" line?

> +
> + /* see scaled_ppm_to_ppb() in ptp_clock.c for details */
> + ppb = 1 + scaled_ppm;
> + ppb *= 125;
> + ppb *= KSZ_PTP_INC_NS;
> + ppb <<= KSZ_PTP_SUBNS_BITS - 13;
> + adj = div_s64(ppb, NSEC_PER_SEC);
> +
> + data32 = abs(adj);
> + data32 &= BIT_MASK(30) - 1;
> + if (adj >= 0)
> + data32 |= PTP_RATE_DIR;
> +
> + ret = ksz_write32(dev, REG_PTP_SUBNANOSEC_RATE, data32);
> + if (ret)
> + return ret;
> + }
> +
> + ret = ksz_read16(dev, REG_PTP_CLK_CTRL, &data16);
> + if (ret)
> + return ret;
> +
> + if (scaled_ppm)
> + data16 |= PTP_CLK_ADJ_ENABLE;
> + else
> + data16 &= ~PTP_CLK_ADJ_ENABLE;
> +
> + ret = ksz_write16(dev, REG_PTP_CLK_CTRL, data16);
> + if (ret)
> + return ret;
> +
> + return 0;
> +}
> +
> +static int ksz9477_ptp_adjtime(struct ptp_clock_info *ptp, s64 delta)
> +{
> + struct ksz_device *dev = container_of(ptp, struct ksz_device, ptp_caps);
> + s32 sec, nsec;
> + u16 data16;
> + int ret;
> +
> + mutex_lock(&dev->ptp_mutex);

You're skipping the mutex in ksz9477_ptp_adjfine, is that intentional or
just a proof that it's useless? You should add a comment at its
declaration site about what it's meant to protect.

> +
> + /* do not use ns_to_timespec64(), both sec and nsec are subtracted by hw */
> + sec = div_s64_rem(delta, NSEC_PER_SEC, &nsec);
> +
> + ret = ksz_write32(dev, REG_PTP_RTC_NANOSEC, abs(nsec));
> + if (ret)
> + goto error_return;
> +
> + /* contradictory to the data sheet, seconds are also considered */
> + ret = ksz_write32(dev, REG_PTP_RTC_SEC, abs(sec));
> + if (ret)
> + goto error_return;
> +
> + ret = ksz_read16(dev, REG_PTP_CLK_CTRL, &data16);
> + if (ret)
> + goto error_return;
> +
> + data16 |= PTP_STEP_ADJ;
> + if (delta < 0)
> + data16 &= ~PTP_STEP_DIR; /* 0: subtract */
> + else
> + data16 |= PTP_STEP_DIR; /* 1: add */
> +
> + ret = ksz_write16(dev, REG_PTP_CLK_CTRL, data16);
> + if (ret)
> + goto error_return;
> +
> +error_return:
> + mutex_unlock(&dev->ptp_mutex);
> + return ret;
> +}
> +
> +static int _ksz9477_ptp_gettime(struct ksz_device *dev, struct timespec64 *ts)
> +{
> + u32 nanoseconds;
> + u32 seconds;
> + u16 data16;
> + u8 phase;
> + int ret;
> +
> + /* Copy current PTP clock into shadow registers */
> + ret = ksz_read16(dev, REG_PTP_CLK_CTRL, &data16);
> + if (ret)
> + return ret;
> +
> + data16 |= PTP_READ_TIME;
> +
> + ret = ksz_write16(dev, REG_PTP_CLK_CTRL, data16);
> + if (ret)
> + return ret;
> +
> + /* Read from shadow registers */
> + ret = ksz_read8(dev, REG_PTP_RTC_SUB_NANOSEC__2, &phase);
> + if (ret)
> + return ret;
> + ret = ksz_read32(dev, REG_PTP_RTC_NANOSEC, &nanoseconds);
> + if (ret)
> + return ret;
> + ret = ksz_read32(dev, REG_PTP_RTC_SEC, &seconds);
> + if (ret)
> + return ret;
> +
> + ts->tv_sec = seconds;
> + ts->tv_nsec = nanoseconds + phase * 8;
> +
> + return 0;
> +}
> +
> +static int ksz9477_ptp_gettime(struct ptp_clock_info *ptp, struct timespec64 *ts)
> +{
> + struct ksz_device *dev = container_of(ptp, struct ksz_device, ptp_caps);
> + int ret;
> +
> + mutex_lock(&dev->ptp_mutex);
> + ret = _ksz9477_ptp_gettime(dev, ts);
> + mutex_unlock(&dev->ptp_mutex);
> +
> + return ret;
> +}
> +
> +static int ksz9477_ptp_settime(struct ptp_clock_info *ptp, struct timespec64 const *ts)
> +{
> + struct ksz_device *dev = container_of(ptp, struct ksz_device, ptp_caps);
> + u16 data16;
> + int ret;
> +
> + mutex_lock(&dev->ptp_mutex);
> +
> + /* Write to shadow registers */
> +
> + /* clock phase */
> + ret = ksz_read16(dev, REG_PTP_RTC_SUB_NANOSEC__2, &data16);
> + if (ret)
> + goto error_return;
> +
> + data16 &= ~PTP_RTC_SUB_NANOSEC_M;
> +
> + ret = ksz_write16(dev, REG_PTP_RTC_SUB_NANOSEC__2, data16);
> + if (ret)
> + goto error_return;
> +
> + /* nanoseconds */
> + ret = ksz_write32(dev, REG_PTP_RTC_NANOSEC, ts->tv_nsec);
> + if (ret)
> + goto error_return;
> +
> + /* seconds */
> + ret = ksz_write32(dev, REG_PTP_RTC_SEC, ts->tv_sec);
> + if (ret)
> + goto error_return;
> +
> + /* Load PTP clock from shadow registers */
> + ret = ksz_read16(dev, REG_PTP_CLK_CTRL, &data16);
> + if (ret)
> + goto error_return;
> +
> + data16 |= PTP_LOAD_TIME;
> +
> + ret = ksz_write16(dev, REG_PTP_CLK_CTRL, data16);
> + if (ret)
> + goto error_return;
> +
> +error_return:
> + mutex_unlock(&dev->ptp_mutex);
> + return ret;
> +}
> +
> +static int ksz9477_ptp_enable(struct ptp_clock_info *ptp, struct ptp_clock_request *req, int on)
> +{
> + return -ENOTTY;
> +}

How about -EOPNOTSUPP? I think -ENOTTY is reserved for "invalid ioctl on
the PTP clock", you wouldn't want to confuse a user into thinking that
they got the ioctls wrong (such as with the recent introduction of
PTP_PEROUT_REQUEST2 etc) when in fact the error comes from the driver.

\
 
 \ /
  Last update: 2020-11-13 00:48    [W:0.260 / U:0.472 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site