lkml.org 
[lkml]   [2020]   [Nov]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH V2] PCI: dwc: Add support to configure for ECRC
Date
On 11/11/20, 7:12 AM, Vidya Sagar wrote:
>
> DesignWare core has a TLP digest (TD) override bit in one of the control
> registers of ATU. This bit also needs to be programmed for proper ECRC
> functionality. This is currently identified as an issue with DesignWare
> IP version 4.90a.
>
> Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
> Acked-by: Bjorn Helgaas <bhelgaas@google.com>
> ---
> V2:
> * Addressed Bjorn's comments
>
> drivers/pci/controller/dwc/pcie-designware.c | 52 ++++++++++++++++++--
> drivers/pci/controller/dwc/pcie-designware.h | 1 +
> 2 files changed, 49 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/pci/controller/dwc/pcie-designware.c b/drivers/pci/controller/dwc/pcie-designware.c
> index c2dea8fc97c8..ec0d13ab6bad 100644
> --- a/drivers/pci/controller/dwc/pcie-designware.c
> +++ b/drivers/pci/controller/dwc/pcie-designware.c
> @@ -225,6 +225,46 @@ static void dw_pcie_writel_ob_unroll(struct dw_pcie *pci, u32 index, u32 reg,
> dw_pcie_writel_atu(pci, offset + reg, val);
> }
>
> +static inline u32 dw_pcie_enable_ecrc(u32 val)

What is the reason to use inline here?


Best regards,
Jingoo Han

> +{
> + /*
> + * DesignWare core version 4.90A has this strange design issue
> + * where the 'TD' bit in the Control register-1 of the ATU outbound
> + * region acts like an override for the ECRC setting i.e. the presence
> + * of TLP Digest(ECRC) in the outgoing TLPs is solely determined by
> + * this bit. This is contrary to the PCIe spec which says that the
> + * enablement of the ECRC is solely determined by the AER registers.
> + *
> + * Because of this, even when the ECRC is enabled through AER
> + * registers, the transactions going through ATU won't have TLP Digest
> + * as there is no way the AER sub-system could program the TD bit which
> + * is specific to DesignWare core.
> + *
> + * The best way to handle this scenario is to program the TD bit
> + * always. It affects only the traffic from root port to downstream
> + * devices.
> + *
> + * At this point,
> + * When ECRC is enabled in AER registers, everything works normally
> + * When ECRC is NOT enabled in AER registers, then,
> + * on Root Port:- TLP Digest (DWord size) gets appended to each packet
> + * even through it is not required. Since downstream
> + * TLPs are mostly for configuration accesses and BAR
> + * accesses, they are not in critical path and won't
> + * have much negative effect on the performance.
> + * on End Point:- TLP Digest is received for some/all the packets coming
> + * from the root port. TLP Digest is ignored because,
> + * as per the PCIe Spec r5.0 v1.0 section 2.2.3
> + * "TLP Digest Rules", when an endpoint receives TLP
> + * Digest when its ECRC check functionality is disabled
> + * in AER registers, received TLP Digest is just ignored.
> + * Since there is no issue or error reported either side, best way to
> + * handle the scenario is to program TD bit by default.
> + */
> +
> + return val | PCIE_ATU_TD;
> +}
> +
> static void dw_pcie_prog_outbound_atu_unroll(struct dw_pcie *pci, u8 func_no,
> int index, int type,
> u64 cpu_addr, u64 pci_addr,
> @@ -245,8 +285,10 @@ static void dw_pcie_prog_outbound_atu_unroll(struct dw_pcie *pci, u8 func_no,
> lower_32_bits(pci_addr));
> dw_pcie_writel_ob_unroll(pci, index, PCIE_ATU_UNR_UPPER_TARGET,
> upper_32_bits(pci_addr));
> - dw_pcie_writel_ob_unroll(pci, index, PCIE_ATU_UNR_REGION_CTRL1,
> - type | PCIE_ATU_FUNC_NUM(func_no));
> + val = type | PCIE_ATU_FUNC_NUM(func_no);
> + if (pci->version == 0x490A)
> + val = dw_pcie_enable_ecrc(val);
> + dw_pcie_writel_ob_unroll(pci, index, PCIE_ATU_UNR_REGION_CTRL1, val);
> dw_pcie_writel_ob_unroll(pci, index, PCIE_ATU_UNR_REGION_CTRL2,
> PCIE_ATU_ENABLE);
>
> @@ -292,8 +334,10 @@ static void __dw_pcie_prog_outbound_atu(struct dw_pcie *pci, u8 func_no,
> lower_32_bits(pci_addr));
> dw_pcie_writel_dbi(pci, PCIE_ATU_UPPER_TARGET,
> upper_32_bits(pci_addr));
> - dw_pcie_writel_dbi(pci, PCIE_ATU_CR1, type |
> - PCIE_ATU_FUNC_NUM(func_no));
> + val = type | PCIE_ATU_FUNC_NUM(func_no);
> + if (pci->version == 0x490A)
> + val = dw_pcie_enable_ecrc(val);
> + dw_pcie_writel_dbi(pci, PCIE_ATU_CR1, val);
> dw_pcie_writel_dbi(pci, PCIE_ATU_CR2, PCIE_ATU_ENABLE);
>
> /*
> diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h
> index 9d2f511f13fa..285c0ae364ae 100644
> --- a/drivers/pci/controller/dwc/pcie-designware.h
> +++ b/drivers/pci/controller/dwc/pcie-designware.h
> @@ -88,6 +88,7 @@
> #define PCIE_ATU_TYPE_IO 0x2
> #define PCIE_ATU_TYPE_CFG0 0x4
> #define PCIE_ATU_TYPE_CFG1 0x5
> +#define PCIE_ATU_TD BIT(8)
> #define PCIE_ATU_FUNC_NUM(pf) ((pf) << 20)
> #define PCIE_ATU_CR2 0x908
> #define PCIE_ATU_ENABLE BIT(31)
> --
> 2.17.1

\
 
 \ /
  Last update: 2020-11-11 17:28    [W:0.090 / U:0.868 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site