lkml.org 
[lkml]   [2020]   [Nov]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v4 6/7] gpio: exar: switch to using regmap
On Tue, Nov 10, 2020 at 5:43 PM Andy Shevchenko
<andy.shevchenko@gmail.com> wrote:
>
> On Tue, Nov 10, 2020 at 6:37 PM Bartosz Golaszewski
> <bgolaszewski@baylibre.com> wrote:
> > On Tue, Nov 10, 2020 at 5:17 PM Andy Shevchenko
> > <andriy.shevchenko@linux.intel.com> wrote:
>
> ...
>
> > > > > > > +static const struct regmap_config exar_regmap_config = {
> > > > > > > + .name = "exar-gpio",
> > > > > > > + .reg_bits = 16,
> > > > > >
> > > > > > As per previous version comment.
> > > > > >
> > > > > > Hold on, the registers are 16-bit wide, but their halves are sparsed!
> > > > > > So, I guess 8 and 8 with helpers to get hi and lo parts are essential.
> > > > > >
> > > > > >
> > > > > > TABLE 5: DEVICE CONFIGURATION REGISTERS SHOWN IN BYTE ALIGNMENT
> > > > > >
> > > > > > > + .val_bits = 8,
> > > > > > > +};
> > > > > >
> > > > > > This is basically represents two banks out of 6 8-bit registers each.
> > > > >
> > > > > ...which makes me wonder if gpio-regmap can be utilized here...
> > > > >
> > > >
> > > > But the address width won't affect the actuall accessing of 8 bits
> > > > registers in an mmio regmap. Internally the mmio regmap does pretty
> > > > much the same thing the previous driver did: call readb()/writeb() on
> > > > 8-bit "chunks" of the banks.
> > >
> > > It will affect reg dump in debugfs. I would really narrow down the register
> > > address space in the config, otherwise that debugfs facility will screw up a
> > > lot of things.
> > >
> > > So, and to be on pedantic side...
> > >
> > > "The Device Configuration Registers and the two individual UART Configuration
> > > Registers of the XR17V352 occupy 2K of PCI bus memory address space."
> > >
> > > 11 seems the correct value for the address width.
> >
> > I take it as a typo and assume you meant 16. So the patch should be
> > correct and your review tag is good to go?
>
> It's not a typo. But thinking again. This is basically done in regmap
> to support serial buses. Here we have MMIO pretty much with 32-bit or
> 64-bit address accesses. I didn't dig into regmap implementation to
> understand the consequences of changing this to the different values
> (it seems like rather offset, and in this case 11 is a correct one,
> not a typo, and regmap is okay with that).
> But I would rather ask Jan to actually mount debugfs and dump
> registers and see if it screws up the UART (because it may go all over
> important registers), that's why I think this configuration is still
> missing some strict rules about what addresses (offsets) driver may or
> may not access.

Ok now I get it. Yes 11 seems to be right in this case for the max
address. We can implement the readable/writable callbacks to be very
strict about the register accesses but isn't it overkill? This driver
is very small and only accesses a couple registers. I don't see such
strict checking very often except for very complicated modules (like
pca953x you mentioned).

Bartosz

\
 
 \ /
  Last update: 2020-11-10 17:53    [W:0.038 / U:0.352 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site