lkml.org 
[lkml]   [2020]   [Oct]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [RESEND PATCH v3 1/3] dt-bindings: pinctrl: Add bindings for pinctrl-mchp-sgpio driver
Date

Hi Rob!

Rob Herring writes:

> On Tue, Oct 06, 2020 at 04:25:30PM +0200, Lars Povlsen wrote:
>> This adds DT bindings for the Microsemi/Microchip SGPIO controller,
>> bindings microchip,sparx5-sgpio, mscc,ocelot-sgpio and
>> mscc,luton-sgpio.
>>
>> Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
>> ---
>> .../pinctrl/microchip,sparx5-sgpio.yaml | 127 ++++++++++++++++++
>> 1 file changed, 127 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml b/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml
>> new file mode 100644
>> index 000000000000..e3618ed28165
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml
>> @@ -0,0 +1,127 @@
>> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/pinctrl/microchip,sparx5-sgpio.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Microsemi/Microchip Serial GPIO controller
>> +
>> +maintainers:
>> + - Lars Povlsen <lars.povlsen@microchip.com>
>> +
>> +description: |
>> + By using a serial interface, the SIO controller significantly extend
>> + the number of available GPIOs with a minimum number of additional
>> + pins on the device. The primary purpose of the SIO controllers is to
>> + connect control signals from SFP modules and to act as an LED
>> + controller.
>> +
>> +properties:
>> + $nodename:
>> + pattern: "^gpio@[0-9a-f]+$"
>> +
>> + compatible:
>> + enum:
>> + - microchip,sparx5-sgpio
>> + - mscc,ocelot-sgpio
>> + - mscc,luton-sgpio
>> +
>> + "#address-cells":
>> + const: 1
>> +
>> + "#size-cells":
>> + const: 0
>> +
>> + reg:
>> + maxItems: 1
>> +
>> + clocks:
>> + maxItems: 1
>> +
>> + microchip,sgpio-port-ranges:
>> + description: This is a sequence of tuples, defining intervals of
>> + enabled ports in the serial input stream. The enabled ports must
>> + match the hardware configuration in order for signals to be
>> + properly written/read to/from the controller holding
>> + registers. Being tuples, then number of arguments must be
>> + even. The tuples mast be ordered (low, high) and are
>> + inclusive. Arguments must be between 0 and 31.
>> + $ref: /schemas/types.yaml#/definitions/uint32-array
>> + minItems: 2
>> + maxItems: 64
>> +
>> + microchip,sgpio-frequency:
>> + description: The sgpio controller frequency (Hz). This dictates
>> + the serial bitstream speed, which again affects the latency in
>> + getting control signals back and forth between external shift
>> + registers. The speed must be no larger than half the system
>> + clock, and larger than zero.
>> + $ref: /schemas/types.yaml#/definitions/uint32
>> + minimum: 1
>> + default: 12500000
>> +
>> +patternProperties:
>> + "^gpio-(port|controller)@[01]$":
>
> gpio@... is correct here as the node is a gpio-controller (no, we're
> not consistent).

OK, fine by me.

>
>> + type: object
>> + properties:
>> + compatible:
>> + const: microchip,sparx5-sgpio-bank
>> +
>> + reg:
>> + maxItems: 1
>> +
>> + gpio-controller: true
>> +
>> + '#gpio-cells':
>> + const: 3
>> +
>> + ngpios:
>> + minimum: 1
>> + maximum: 128
>> +
>> + required:
>> + - compatible
>> + - reg
>> + - gpio-controller
>> + - '#gpio-cells'
>> + - ngpios
>> +
>> + additionalProperties: false
>> +
>> +additionalProperties: false
>> +
>> +required:
>> + - compatible
>> + - reg
>> + - clocks
>> + - microchip,sgpio-port-ranges
>> + - "#address-cells"
>> + - "#size-cells"
>> +
>> +examples:
>> + - |
>> + sgpio2: gpio@1101059c {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + compatible = "microchip,sparx5-sgpio";
>> + clocks = <&sys_clk>;
>> + pinctrl-0 = <&sgpio2_pins>;
>> + pinctrl-names = "default";
>> + reg = <0x1101059c 0x100>;
>> + microchip,sgpio-port-ranges = <0 0 16 18 28 31>;
>
> Since it's tuples, do:
>
> <0 0>, <16 18>, <28 31>

Yes, that will add clarity.

>
>> + microchip,sgpio-frequency = <25000000>;
>
> Some whitespace issues here.
>

Will fix that.

>
>> + sgpio_in2: gpio-controller@0 {
>> + reg = <0>;
>> + compatible = "microchip,sparx5-sgpio-bank";
>> + gpio-controller;
>> + #gpio-cells = <3>;
>> + ngpios = <96>;
>> + };
>> + sgpio_out2: gpio-controller@1 {
>> + compatible = "microchip,sparx5-sgpio-bank";
>> + reg = <1>;
>> + gpio-controller;
>> + #gpio-cells = <3>;
>> + ngpios = <96>;
>> + };
>> + };
>> --
>> 2.25.1

Thank you for your comments, I will refresh the series shortly.

---Lars

--
Lars Povlsen,
Microchip

\
 
 \ /
  Last update: 2020-10-07 13:08    [W:0.039 / U:0.048 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site