lkml.org 
[lkml]   [2020]   [Oct]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v5 1/4] dt-bindings: media: imx258: add bindings for IMX258 sensor
On Tue, Oct 20, 2020 at 02:58:52PM +0200, Krzysztof Kozlowski wrote:
> On Tue, Oct 20, 2020 at 03:46:54PM +0300, Sakari Ailus wrote:
> > On Tue, Oct 20, 2020 at 02:26:21PM +0200, Krzysztof Kozlowski wrote:
> > > On Tue, Oct 20, 2020 at 03:00:58PM +0300, Sakari Ailus wrote:
> > > > Hi Krzysztof,
> > > >
> > > > On Tue, Oct 20, 2020 at 12:54:09PM +0200, Krzysztof Kozlowski wrote:
> > > > > On Tue, 20 Oct 2020 at 12:38, Sakari Ailus <sakari.ailus@linux.intel.com> wrote:
> > > > > >
> > > > > > Hi Krzysztof,
> > > > > >
> > > > > > On Mon, Oct 19, 2020 at 07:02:44PM +0200, Krzysztof Kozlowski wrote:
> > > > > > > Add bindings for the IMX258 camera sensor. The bindings, just like the
> > > > > > > driver, are quite limited, e.g. do not support regulator supplies.
> > > > > > >
> > > > > > > Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
> > > > > > > Reviewed-by: Rob Herring <robh@kernel.org>
> > > > > > >
> > > > > > > ---
> > > > > > >
> > > > > > > Changes since v4:
> > > > > > > 1. Add clock-lanes,
> > > > > > > 2. Add Rob's review,
> > > > > > > 3. Add one more example and extend existing one,
> > > > > > > 4. Add common clock properties (assigned-*).
> > > > > >
> > > > > > Using the assigned-* clock properties may be workable for this driver at
> > > > > > the moment. But using these properties does not guarantee the external
> > > > > > clock frequency intended to be used on the hardware.
> > > > >
> > > > > It guarantees it. The clock frequency will be as expected (except if
> > > > > someone misconfigures the DTS).
> > > >
> > > > Is that guaranteed?
> > > >
> > > > I'm not saying no to the approach, but if we change how camera sensor DT
> > > > bindings are defined, I'd prefer an informed decision is made on the
> > > > matter.
> > > >
> > > > >
> > > > > > Using other
> > > > > > frequencies *is not* expected to work. That applies to this driver as well.
> > > > >
> > > > > This is the binding which is HW description. According to HW datasheet
> > > > > other frequencies from described range are accepted and expected to
> > > > > work.
> > > >
> > > > As per datasheet, yes, different external clock frequencies can be used.
> > > > But the link frequency is still not independent of the external clock
> > > > frequency.
> > > >
> > > > The properties of the sensor's PLL tree determines what can be achieved
> > > > given a certain external clock frequency. So picking a wrong external clock
> > > > frequency quite possibly means that none of the designated link frequencies
> > > > are available, rendering the sensor inoperable.
> > >
> > > The driver then controls the HW and knows exactly what is needed. If
> > > link frequency (which has its own DT property) requires some clock
> > > frequency, the driver will configure the clock to that value. The same
> >
> > Well it doesn't if it doesn't get that information from DT.
>
> It will get it - via clk_get_rate(). You do not need DT for this.
>
> > The frequency is usually a range, and looking at these bindings, it's from
> > 6 MHz to 27 MHz. That'd be a lot of frequencies for a driver to try.
>
> It does not have to try all of them. Assuming link frequency is fixed,
> just use any matching (or hard-coded) input clock frequency. Since the
> input clock frequency most likely will be set with assigned-clock-rates,
> there will be no job to do for the driver at all. Unless the driver
> wants to do something more, of course.
>
> >
> > > going other direction. Driver has the knowledge about both its input
> > > clock and link frequency, therefore it can make the best decision.
> >
> > Again you're assuming a particular driver implementation.
>
> Actually not, I am talking about bindings as far away from the driver
> implementation as possible. This is why some specific frequency *is
> not* part of the bindings.
>
> >
> > Typically only a few frequencies are really available on platforms, so a in
> > practice a driver would not be able to get any requested frequency. I
> > wouldn't start hard-coding every possible frequency to camera sensor
> > drivers
>
> If the driver cannot get requested frequency which it apparently
> requires, there is nothing more to do. It's broken HW implementation.
> The input clock must be matching requirements, regardless of what
> property you put in DT. You can add "clock-frequency" property, you can
> even add "really-i-require-clock-frequency" but if the real HW input
> clock does not have, it won't work.
>
> IOW, adding "clock-frequency" property does not change the reality - the
> board (HW) must provide given frequency so the entire system works.
>
> >
> > > > > > This, instead of the clock-frequency property, effectively removes the
> > > > > > ability to set the correct frequency from the driver, at least with current
> > > > > > set of the used APIs.
> > > > >
> > > > > It seems you confuse DT bindings with some specific driver
> > > > > implementation. Bindings do not describe the driver behavior but the
> > > > > HW. The ability to set the correct frequency from the driver is not
> > > > > removed. It was never part of the bindings and never should. It is
> > > > > part of the driver.
> > > > >
> > > > > >
> > > > > > I suppose you could add a function to set the assigned clock frequency and
> > > > > > keep it, just as clk_set_rate_exclusive does?
> > >
> > > I did not reply to this comment, so let me know. Of course, one could
> > > add such functions. It's not a job for DT bindings, though.
> >
> > I'm not suggesting to add it to DT binding patch. What I'm saying that with
> > this approach is looks like it may well be needed.
>
> New properties can always be added to DT. However existing properties
> cannot be removed. Their meaning or values cannot be changed.

Any more comments on the bindings or the patchset?

Best regards,
Krzysztof

\
 
 \ /
  Last update: 2020-10-29 00:18    [W:0.057 / U:0.036 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site