lkml.org 
[lkml]   [2020]   [Oct]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v4 5/6] dt-bindings: spi: Convert cadence-quadspi.txt to cadence-quadspi.yaml
From
Date
Hi Rob,

Thank you for your review comments...

On 28/10/2020 11:07 pm, Rob Herring wrote:
> On Tue, Oct 27, 2020 at 04:22:50PM +0800, Ramuthevar,Vadivel MuruganX wrote:
>> From: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
>>
>> Convert the cadence-quadspi.txt documentation to cadence-quadspi.yaml
>> remove the cadence-quadspi.txt from Documentation/devicetree/bindings/spi/
>>
>> Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
>> ---
>> .../devicetree/bindings/spi/cadence-quadspi.txt | 67 ----------
>> .../devicetree/bindings/spi/cadence-quadspi.yaml | 148 +++++++++++++++++++++
>> 2 files changed, 148 insertions(+), 67 deletions(-)
>> delete mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.txt
>> create mode 100644 Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt b/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
>> deleted file mode 100644
>> index 945be7d5b236..000000000000
>> --- a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
>> +++ /dev/null
>> @@ -1,67 +0,0 @@
>> -* Cadence Quad SPI controller
>> -
>> -Required properties:
>> -- compatible : should be one of the following:
>> - Generic default - "cdns,qspi-nor".
>> - For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor".
>> - For TI AM654 SoC - "ti,am654-ospi", "cdns,qspi-nor".
>> -- reg : Contains two entries, each of which is a tuple consisting of a
>> - physical address and length. The first entry is the address and
>> - length of the controller register set. The second entry is the
>> - address and length of the QSPI Controller data area.
>> -- interrupts : Unit interrupt specifier for the controller interrupt.
>> -- clocks : phandle to the Quad SPI clock.
>> -- cdns,fifo-depth : Size of the data FIFO in words.
>> -- cdns,fifo-width : Bus width of the data FIFO in bytes.
>> -- cdns,trigger-address : 32-bit indirect AHB trigger address.
>> -
>> -Optional properties:
>> -- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not.
>> -- cdns,rclk-en : Flag to indicate that QSPI return clock is used to latch
>> - the read data rather than the QSPI clock. Make sure that QSPI return
>> - clock is populated on the board before using this property.
>> -
>> -Optional subnodes:
>> -Subnodes of the Cadence Quad SPI controller are spi slave nodes with additional
>> -custom properties:
>> -- cdns,read-delay : Delay for read capture logic, in clock cycles
>> -- cdns,tshsl-ns : Delay in nanoseconds for the length that the master
>> - mode chip select outputs are de-asserted between
>> - transactions.
>> -- cdns,tsd2d-ns : Delay in nanoseconds between one chip select being
>> - de-activated and the activation of another.
>> -- cdns,tchsh-ns : Delay in nanoseconds between last bit of current
>> - transaction and deasserting the device chip select
>> - (qspi_n_ss_out).
>> -- cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low
>> - and first bit transfer.
>> -- resets : Must contain an entry for each entry in reset-names.
>> - See ../reset/reset.txt for details.
>> -- reset-names : Must include either "qspi" and/or "qspi-ocp".
>> -
>> -Example:
>> -
>> - qspi: spi@ff705000 {
>> - compatible = "cdns,qspi-nor";
>> - #address-cells = <1>;
>> - #size-cells = <0>;
>> - reg = <0xff705000 0x1000>,
>> - <0xffa00000 0x1000>;
>> - interrupts = <0 151 4>;
>> - clocks = <&qspi_clk>;
>> - cdns,is-decoded-cs;
>> - cdns,fifo-depth = <128>;
>> - cdns,fifo-width = <4>;
>> - cdns,trigger-address = <0x00000000>;
>> - resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>;
>> - reset-names = "qspi", "qspi-ocp";
>> -
>> - flash0: n25q00@0 {
>> - ...
>> - cdns,read-delay = <4>;
>> - cdns,tshsl-ns = <50>;
>> - cdns,tsd2d-ns = <50>;
>> - cdns,tchsh-ns = <4>;
>> - cdns,tslch-ns = <4>;
>> - };
>> - };
>> diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
>> new file mode 100644
>> index 000000000000..da11cb3bedeb
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/spi/cadence-quadspi.yaml
>> @@ -0,0 +1,148 @@
>> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/spi/cadence-quadspi.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Cadence Quad SPI controller
>> +
>> +maintainers:
>> + - Vadivel Murugan <vadivel.muruganx.ramuthevar@intel.com>
>> +
>> +allOf:
>> + - $ref: "spi-controller.yaml#"
>> +
>> +properties:
>> + compatible:
>> + oneOf:
>> + - items:
>> + - const: cdns,qspi-nor
>> + - const: ti,k2g-qspi, cdns,qspi-nor
>> + - const: ti,am654-ospi, cdns,qspi-nor
>
> This is still not right. 'const' points to a single string which is not
> what you want.
oh my bad, you are right, will update,thanks!

Regards
Vadivel
>
>> +
>> + reg:
>> + items:
>> + - description: the controller register set
>> + - description: the controller data area
>> +
>> + interrupts:
>> + maxItems: 1
>> +
>> + clocks:
>> + maxItems: 1
>> +
>> + cdns,fifo-depth:
>> + description:
>> + Size of the data FIFO in words.
>> + $ref: "/schemas/types.yaml#/definitions/uint32"
>> + enum: [ 128, 256 ]
>> + default: 128
>> +
>> + cdns,fifo-width:
>> + $ref: /schemas/types.yaml#/definitions/uint32
>> + description:
>> + Bus width of the data FIFO in bytes.
>> + default: 4
>> +
>> + cdns,trigger-address:
>> + $ref: /schemas/types.yaml#/definitions/uint32
>> + description:
>> + 32-bit indirect AHB trigger address.
>> +
>> + cdns,is-decoded-cs:
>> + type: boolean
>> + description:
>> + Flag to indicate whether decoder is used or not.
>> +
>> + cdns,rclk-en:
>> + type: boolean
>> + description:
>> + Flag to indicate that QSPI return clock is used to latch the read
>> + data rather than the QSPI clock. Make sure that QSPI return clock
>> + is populated on the board before using this property.
>> +
>> + resets:
>> + maxItems : 2
>> +
>> + reset-names:
>> + minItems: 1
>> + maxItems: 2
>> + items:
>> + enum: [ qspi, qspi-ocp ]
>> +
>> +# subnode's properties
>> +patternProperties:
>> + "@[0-9a-f]+$":
>> + type: object
>> + description:
>> + flash device uses the subnodes below defined properties.
>> + properties:
>> + cdns,read-delay:
>> + $ref: /schemas/types.yaml#/definitions/uint32
>> + description:
>> + Delay for read capture logic, in clock cycles.
>> +
>> + cdns,tshsl-ns:
>> + description:
>> + Delay in nanoseconds for the length that the master mode chip select
>> + outputs are de-asserted between transactions.
>> +
>> + cdns,tsd2d-ns:
>> + description:
>> + Delay in nanoseconds between one chip select being de-activated
>> + and the activation of another.
>> +
>> + cdns,tchsh-ns:
>> + description:
>> + Delay in nanoseconds between last bit of current transaction and
>> + deasserting the device chip select (qspi_n_ss_out).
>> +
>> + cdns,tslch-ns:
>> + description:
>> + Delay in nanoseconds between setting qspi_n_ss_out low and
>> + first bit transfer.
>> +
>> +required:
>> + - compatible
>> + - reg
>> + - interrupts
>> + - clocks
>> + - cdns,fifo-depth
>> + - cdns,fifo-width
>> + - cdns,trigger-address
>> + - cdns,is-decoded-cs
>> + - cdns,rclk-en
>> + - resets
>> + - reset-names
>> +
>> +additionalProperties: false
>> +
>> +examples:
>> + - |
>> + qspi: spi@ff705000 {
>> + compatible = "cadence,qspi","cdns,qpsi-nor";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + reg = <0xff705000 0x1000>,
>> + <0xffa00000 0x1000>;
>> + interrupts = <0 151 4>;
>> + clocks = <&qspi_clk>;
>> + cdns,fifo-depth = <128>;
>> + cdns,fifo-width = <4>;
>> + cdns,trigger-address = <0x00000000>;
>> + resets = <&rst 0x1>, <&rst 0x2>;
>> + reset-names = "qspi", "qspi-ocp";
>> +
>> + flash@0 {
>> + compatible = "jedec,spi-nor";
>> + reg = <0x0>;
>> + cdns,read-delay = <4>;
>> + cdns,tshsl-ns = <50>;
>> + cdns,tsd2d-ns = <50>;
>> + cdns,tchsh-ns = <4>;
>> + cdns,tslch-ns = <4>;
>> + };
>> +
>> + };
>> +
>> +...
>> --
>> 2.11.0
>>

\
 
 \ /
  Last update: 2020-10-29 02:59    [W:0.157 / U:0.412 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site