lkml.org 
[lkml]   [2020]   [Oct]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v1 1/2] leds: rt4505: Add support for Richtek RT4505 flash led controller
Hi!

> From: ChiYuan Huang <cy_huang@richtek.com>
>
> Add support for RT4505 flash led controller. It can support up to 1.5A
> flash current with hardware timeout and low input voltage
> protection.

Please use upper-case "LED" everywhere.

This should be 2nd in the series, after DT changes.

> Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
> ---
> drivers/leds/Kconfig | 11 ++
> drivers/leds/Makefile | 1 +
> drivers/leds/leds-rt4505.c | 397 +++++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 409 insertions(+)
> create mode 100644 drivers/leds/leds-rt4505.c

Lets put this into drivers/leds/flash/. (Yes, you'll have to create
it).


> + help
> + This option enables support for the RT4505 flash led controller.

Information where it is used would be welcome here.

> + It can support up to 1.5A flash strobe current with hardware timeout
> + and low input voltage protection.

This does not / should not be here.
> +
> +static int rt4505_torch_brightness_set(struct led_classdev *lcdev, enum led_brightness level)
> +{

80 columns, where easy.

> + struct rt4505_priv *priv = container_of(lcdev, struct rt4505_priv, flash.led_cdev);
> + u32 val = 0;
> + int ret;
> +
> + mutex_lock(&priv->lock);
> +
> + if (level != LED_OFF) {
> + ret = regmap_update_bits(priv->regmap, RT4505_REG_ILED, RT4505_ITORCH_MASK,
> + (level - 1) << RT4505_ITORCH_SHIFT);
> + if (ret)
> + goto unlock;
> +
> + val = RT4505_TORCH_SET;
> + }
> +
> + ret = regmap_update_bits(priv->regmap, RT4505_REG_ENABLE, RT4505_ENABLE_MASK, val);
> +
> +unlock:
> + mutex_unlock(&priv->lock);
> + return ret;
> +}

Why is the locking needed? What will the /sys/class/leds interface
look like on system with your flash?

> +static int rt4505_flash_strobe_get(struct led_classdev_flash *fled_cdev, bool *state)
> +{
> + struct rt4505_priv *priv = container_of(fled_cdev, struct rt4505_priv, flash);
> + u32 val;
> + int ret;
> +
> + mutex_lock(&priv->lock);
> +
> + ret = regmap_read(priv->regmap, RT4505_REG_ENABLE, &val);
> + if (ret)
> + goto unlock;
> +
> + *state = ((val & RT4505_FLASH_GET) == RT4505_FLASH_GET) ? true : false;

No need for ? ... part.

> +static bool rt4505_is_accessible_reg(struct device *dev, unsigned int reg)
> +{
> + if (reg == RT4505_REG_RESET || (reg >= RT4505_REG_CONFIG && reg <= RT4505_REG_FLAGS))
> + return true;

Make this two stagements.

Otherwise... looks like easy simple driver, thanks.

Best regards,
Pavel
--
http://www.livejournal.com/~pavelmachek
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2020-10-27 09:30    [W:0.146 / U:0.164 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site