lkml.org 
[lkml]   [2020]   [Oct]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH AUTOSEL 5.4 27/80] ipv6/icmp: l3mdev: Perform icmp error route lookup on source device routing table (v2)
Date
From: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>

[ Upstream commit 272928d1cdacfc3b55f605cb0e9115832ecfb20c ]

As per RFC4443, the destination address field for ICMPv6 error messages
is copied from the source address field of the invoking packet.

In configurations with Virtual Routing and Forwarding tables, looking up
which routing table to use for sending ICMPv6 error messages is
currently done by using the destination net_device.

If the source and destination interfaces are within separate VRFs, or
one in the global routing table and the other in a VRF, looking up the
source address of the invoking packet in the destination interface's
routing table will fail if the destination interface's routing table
contains no route to the invoking packet's source address.

One observable effect of this issue is that traceroute6 does not work in
the following cases:

- Route leaking between global routing table and VRF
- Route leaking between VRFs

Use the source device routing table when sending ICMPv6 error
messages.

[ In the context of ipv4, it has been pointed out that a similar issue
may exist with ICMP errors triggered when forwarding between network
namespaces. It would be worthwhile to investigate whether ipv6 has
similar issues, but is outside of the scope of this investigation. ]

[ Testing shows that similar issues exist with ipv6 unreachable /
fragmentation needed messages. However, investigation of this
additional failure mode is beyond this investigation's scope. ]

Link: https://tools.ietf.org/html/rfc4443
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
net/ipv6/icmp.c | 7 +++++--
net/ipv6/ip6_output.c | 2 --
2 files changed, 5 insertions(+), 4 deletions(-)

diff --git a/net/ipv6/icmp.c b/net/ipv6/icmp.c
index 7d3a3894f785c..50c6305c66d01 100644
--- a/net/ipv6/icmp.c
+++ b/net/ipv6/icmp.c
@@ -482,8 +482,11 @@ static void icmp6_send(struct sk_buff *skb, u8 type, u8 code, __u32 info,
if (__ipv6_addr_needs_scope_id(addr_type)) {
iif = icmp6_iif(skb);
} else {
- dst = skb_dst(skb);
- iif = l3mdev_master_ifindex(dst ? dst->dev : skb->dev);
+ /*
+ * The source device is used for looking up which routing table
+ * to use for sending an ICMP error.
+ */
+ iif = l3mdev_master_ifindex(skb->dev);
}

/*
diff --git a/net/ipv6/ip6_output.c b/net/ipv6/ip6_output.c
index 78d495581d696..475705c62bd5a 100644
--- a/net/ipv6/ip6_output.c
+++ b/net/ipv6/ip6_output.c
@@ -467,8 +467,6 @@ int ip6_forward(struct sk_buff *skb)
* check and decrement ttl
*/
if (hdr->hop_limit <= 1) {
- /* Force OUTPUT device used as source address */
- skb->dev = dst->dev;
icmpv6_send(skb, ICMPV6_TIME_EXCEED, ICMPV6_EXC_HOPLIMIT, 0);
__IP6_INC_STATS(net, idev, IPSTATS_MIB_INHDRERRORS);

--
2.25.1
\
 
 \ /
  Last update: 2020-10-18 21:45    [W:2.006 / U:3.420 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site