lkml.org 
[lkml]   [2020]   [Jan]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v6 00/19] Move PMC clocks into Tegra PMC driver
From
Date

On 1/7/20 3:28 PM, Dmitry Osipenko wrote:
> 08.01.2020 02:24, Sowjanya Komatineni пишет:
>> On 1/7/20 3:01 PM, Dmitry Osipenko wrote:
>>> Hello Sowjanya,
>>>
>>> 07.01.2020 07:13, Sowjanya Komatineni пишет:
>>>> This patch series moves Tegra PMC clocks from clock driver to pmc driver
>>>> along with the device trees changes and audio driver which uses one of
>>>> the pmc clock for audio mclk.
>>>>
>>>> Tegra PMC has clk_out_1, clk_out_2, clk_out_3 and blink controls which
>>>> are currently registered by Tegra clock driver using clk_regiser_mux and
>>>> clk_register_gate which performs direct Tegra PMC register access.
>>>>
>>>> When Tegra PMC is in secure mode, any access from non-secure world will
>>>> not go through.
>>>>
>>>> This patch series adds these Tegra PMC clocks and blink controls to
>>>> Tegra
>>>> PMC driver with PMC as clock provider and removes them from Tegra clock
>>>> driver.
>>>>
>>>> PMC clock clk_out_1 is dedicated for audio mclk from Tegra30 thru
>>>> Tegra210
>>>> and clock driver does inital parent configuration for it and enables
>>>> them.
>>>> But this clock should be taken care by audio driver as there is no need
>>>> to have this clock pre enabled.
>>>>
>>>> So, this series also includes patch that updates ASoC driver to take
>>>> care of parent configuration for mclk if device tree don't specify
>>>> initial parent configuration using assigned-clock-parents and controls
>>>> audio mclk enable/disable during ASoC machine startup and shutdown.
>>>>
>>>> DTs are also updated to use clk_out_1 as audio mclk rather than extern1.
>>>>
>>>> This series also includes a patch for mclk fallback to extern1 when
>>>> retrieving mclk fails to have this backward compatible of new DT with
>>>> old kernels.
>>>>
>>>> [v6]:    Changes between v5 and v6 are
>>>>     - v5 feedback
>>>>     - Added ASoC machine startup and shutdown callbacks to control audio
>>>>       mclk enable/disable and removed default mclk enable from clock
>>>> driver.
>>>>     - Updated tegra_asoc_utils_set_rate to disable mclk only during PLLA
>>>>       rate change and removed disabling PLLA as its already taken
>>>> care by
>>>>       pll clock driver.
>>>>     - Removed tegra_asoc_utils_set_rate call from utils_init as set_rate
>>>>       is set during machine hw_params and during utils_init mclk is
>>>>       already in disabled state and this causes warning during mclk
>>>> disable
>>>>       in utils_set_rate.
>>>>
>>>> [v5]:    Changes between v4 and v5 are
>>>>     - v4 feedback
>>>>     - updated dt-binding pmc YAML schema with more description on power
>>>>       gate nodes and pad configuration state nodes.
>>>>     - update tegra_asoc_utils_set_rate to disable audio mclk only if
>>>>       its in enable state.
>>>>
>>>> [v4]:    Changes between v3 and v4 are
>>>>     - v3 Feedback
>>>>     - Updated clocks clk_m_div2 and clk_m_div4 as osc_div2 and osc_div4.
>>>>       Tegra don't have clk_m_div2, clk_m_div4 and they should actually
>>>>       be osc_div2 and osc_div4 clocks from osc pads.
>>>>     - Fixed PMC clock parents to use osc, osc_div2, osc_div4.
>>>>     - Register each PMC clock as single clock rather than separate
>>>>       mux and gate clocks.
>>>>     - Update ASoC utils to use resource managed APIs rather than
>>>>       using clk_get and clk_put.
>>>>     - Updated device tree and ASoC driver to use clk_out_1 instead of
>>>>       clk_out_1_mux as PMC clocks are registered as single clock.
>>>>     - Update clock driver init_table to not enable audio related clocks
>>>>       as ASoC utils will do audio clock enables.
>>>>
>>>> [v3]:    Changes between v2 and v3 are
>>>>     - Removes set parent of clk_out_1_mux to extern1 and enabling
>>>>       extern1 from the clock driver.
>>>>     - Doesn't enable clk_out_1 and blink by default in pmc driver
>>>>     - Updates ASoC driver to take care of audio mclk parent
>>>>       configuration incase if device tree don't specify assigned
>>>>       clock parent properties and enables mclk using both clk_out_1
>>>>       and extern1.
>>>>     - updates all device trees using extern1 as mclk in sound node
>>>>       to use clk_out_1 from pmc.
>>>>     - patch for YAML format pmc dt-binding
>>>>     - Includes v2 feedback
>>>>
>>>> [v2]:    Changes between v1 and v2 are
>>>>     - v2 includes patches for adding clk_out_1, clk_out_2, clk_out_3,
>>>>       blink controls to Tegra PMC driver and removing clk-tegra-pmc.
>>>>     - feedback related to pmc clocks in Tegra PMC driver from v1
>>>>     - Removed patches for WB0 PLLM overrides and PLLE IDDQ PMC
>>>> programming
>>>>       by the clock driver using helper functions from Tegra PMC.
>>>>
>>>>         Note:
>>>>       To use helper functions from PMC driver, PMC early init need to
>>>>       happen prior to using helper functions and these helper
>>>> functions are
>>>>       for PLLM Override and PLLE IDDQ programming in PMC during
>>>> PLLM/PLLE
>>>>       clock registration which happen in clock_init prior to Tegra PMC
>>>>       probe.
>>>>       Moving PLLM/PLLE clocks registration to happen after Tegra PMC
>>>>       impacts other clocks EMC, MC and corresponding tegra_emc_init and
>>>>       tegra_mc_init.
>>>>       This implementation of configuring PMC registers thru helper
>>>>       functions in clock driver needs proper changes across PMC, Clock,
>>>>       EMC and MC inits to have it work across all Tegra platforms.
>>>>
>>>>       Currently PLLM Override is not enabled in the bootloader so proper
>>>>       patches for this fix will be taken care separately.
>>>>
>>>> [v1]:    v1 includes patches for below fixes.
>>>>     - adding clk_out_1, clk_out_2, clk_out_3, blink controls to Tegra
>>>> PMC
>>>>       driver and removing clk-tegra-pmc.
>>>>     - updated clock provider from tegra_car to pmc in the device tree
>>>>       tegra210-smaug.dts that uses clk_out_2.
>>>>     - Added helper functions in PMC driver for WB0 PLLM overrides and
>>>> PLLE
>>>>       IDDQ programming to use by clock driver and updated clock
>>>> driver to
>>>>       use these helper functions and removed direct PMC access from
>>>> clock
>>>>       driver and all pmc base address references in clock driver.
>>>>
>>>>
>>>>
>>>>
>>>> Sowjanya Komatineni (19):
>>>>    dt-bindings: clock: tegra: Change CLK_M_DIV to OSC_DIV clocks
>>>>    clk: tegra: Change CLK_M_DIV clocks to OSC_DIV clocks
>>>>    clk: tegra: Fix Tegra PMC clock out parents
>>>>    dt-bindings: tegra: Convert Tegra PMC bindings to YAML
>>>>    dt-bindings: soc: tegra-pmc: Add Tegra PMC clock bindings
>>>>    soc: tegra: Add Tegra PMC clocks registration into PMC driver
>>>>    dt-bindings: soc: tegra-pmc: Add id for Tegra PMC 32KHz blink clock
>>>>    soc: tegra: Add support for 32KHz blink clock
>>>>    clk: tegra: Remove tegra_pmc_clk_init along with clk ids
>>>>    dt-bindings: clock: tegra: Remove pmc clock ids from clock
>>>> dt-bindings
>>>>    ASoC: tegra: Use device managed resource APIs to get the clock
>>>>    ASoC: tegra: Add audio mclk configuration
>>>>    ASoC: tegra: Add fallback implementation for audio mclk
>>>>    clk: tegra: Remove audio related clock enables from init_table
>>>>    ARM: dts: tegra: Add clock-cells property to pmc
>>>>    arm64: tegra: Add clock-cells property to Tegra PMC node
>>>>    ARM: tegra: Update sound node clocks in device tree
>>>>    arm64: tegra: smaug: Change clk_out_2 provider to pmc
>>>>    ASoC: nau8825: change Tegra clk_out_2 provider from tegra_car to pmc
>>>>
>>>>   .../bindings/arm/tegra/nvidia,tegra20-pmc.txt      | 300
>>>> -----------------
>>>>   .../bindings/arm/tegra/nvidia,tegra20-pmc.yaml     | 354
>>>> +++++++++++++++++++++
>>>>   .../devicetree/bindings/sound/nau8825.txt          |   2 +-
>>>>   arch/arm/boot/dts/tegra114-dalmore.dts             |   8 +-
>>>>   arch/arm/boot/dts/tegra114.dtsi                    |   4 +-
>>>>   arch/arm/boot/dts/tegra124-apalis-v1.2.dtsi        |   8 +-
>>>>   arch/arm/boot/dts/tegra124-apalis.dtsi             |   8 +-
>>>>   arch/arm/boot/dts/tegra124-jetson-tk1.dts          |   8 +-
>>>>   arch/arm/boot/dts/tegra124-nyan.dtsi               |   8 +-
>>>>   arch/arm/boot/dts/tegra124-venice2.dts             |   8 +-
>>>>   arch/arm/boot/dts/tegra124.dtsi                    |   4 +-
>>>>   arch/arm/boot/dts/tegra20.dtsi                     |   4 +-
>>>>   arch/arm/boot/dts/tegra30-apalis-v1.1.dtsi         |   8 +-
>>>>   arch/arm/boot/dts/tegra30-apalis.dtsi              |   8 +-
>>>>   arch/arm/boot/dts/tegra30-beaver.dts               |   8 +-
>>>>   arch/arm/boot/dts/tegra30-cardhu.dtsi              |   8 +-
>>>>   arch/arm/boot/dts/tegra30-colibri.dtsi             |   8 +-
>>>>   arch/arm/boot/dts/tegra30.dtsi                     |   4 +-
>>>>   arch/arm64/boot/dts/nvidia/tegra132.dtsi           |   4 +-
>>>>   arch/arm64/boot/dts/nvidia/tegra210-smaug.dts      |   2 +-
>>>>   arch/arm64/boot/dts/nvidia/tegra210.dtsi           |   6 +-
>>>>   drivers/clk/tegra/Makefile                         |   1 -
>>>>   drivers/clk/tegra/clk-id.h                         |  11 +-
>>>>   drivers/clk/tegra/clk-tegra-fixed.c                |  32 +-
>>>>   drivers/clk/tegra/clk-tegra-pmc.c                  | 122 -------
>>>>   drivers/clk/tegra/clk-tegra114.c                   |  41 +--
>>>>   drivers/clk/tegra/clk-tegra124.c                   |  46 +--
>>>>   drivers/clk/tegra/clk-tegra20.c                    |   9 +-
>>>>   drivers/clk/tegra/clk-tegra210.c                   |  30 +-
>>>>   drivers/clk/tegra/clk-tegra30.c                    |  31 +-
>>>>   drivers/clk/tegra/clk.h                            |   1 -
>>>>   drivers/soc/tegra/pmc.c                            | 352
>>>> ++++++++++++++++++++
>>>>   include/dt-bindings/clock/tegra114-car.h           |  18 +-
>>>>   include/dt-bindings/clock/tegra124-car-common.h    |  18 +-
>>>>   include/dt-bindings/clock/tegra20-car.h            |   2 +-
>>>>   include/dt-bindings/clock/tegra210-car.h           |  18 +-
>>>>   include/dt-bindings/clock/tegra30-car.h            |  18 +-
>>>>   include/dt-bindings/soc/tegra-pmc.h                |  16 +
>>>>   sound/soc/tegra/tegra_alc5632.c                    |  28 +-
>>>>   sound/soc/tegra/tegra_asoc_utils.c                 | 125 ++++----
>>>>   sound/soc/tegra/tegra_asoc_utils.h                 |   3 +-
>>>>   sound/soc/tegra/tegra_max98090.c                   |  43 ++-
>>>>   sound/soc/tegra/tegra_rt5640.c                     |  43 ++-
>>>>   sound/soc/tegra/tegra_rt5677.c                     |  28 +-
>>>>   sound/soc/tegra/tegra_sgtl5000.c                   |  28 +-
>>>>   sound/soc/tegra/tegra_wm8753.c                     |  43 ++-
>>>>   sound/soc/tegra/tegra_wm8903.c                     |  43 ++-
>>>>   sound/soc/tegra/tegra_wm9712.c                     |   8 +-
>>>>   sound/soc/tegra/trimslice.c                        |  39 ++-
>>>>   49 files changed, 1192 insertions(+), 777 deletions(-)
>>>>   delete mode 100644
>>>> Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
>>>>   create mode 100644
>>>> Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.yaml
>>>>   delete mode 100644 drivers/clk/tegra/clk-tegra-pmc.c
>>>>   create mode 100644 include/dt-bindings/soc/tegra-pmc.h
>>>>
>>> I briefly looked through the patches and tested them in all possible
>>> configurations. For now everything looks and works well.
>>>
>>> You could add this to all patches:
>>>
>>> Tested-by: Dmitry Osipenko <digetx@gmail.com>
>>> Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
>> Thanks Dmitry
> Actually, it will be more accurate if you will add my t-b only to the
> T20/30 patches. I only looked through the T114+ patches without testing
> them, thanks.

Most of patches has changes to t20 through t210.

Just to be clear, do you meant to add Tested-by to patches 6, 8, 11, 12,
13 and Reviewed-by tag to all patches?

\
 
 \ /
  Last update: 2020-01-08 01:03    [W:0.086 / U:2.196 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site