lkml.org 
[lkml]   [2020]   [Jan]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 1/3] arm64: dts: allwinner: h6: tanix-tx6: enable emmc
Hi,

On Fri, Jan 17, 2020 at 07:18:58PM +0100, Jernej Škrabec wrote:
> Dne petek, 17. januar 2020 ob 19:14:27 CET je Maxime Ripard napisal(a):
> > On Wed, Jan 15, 2020 at 08:34:41PM +0100, Jernej Skrabec wrote:
> > > Tanix TX6 has 32 GiB eMMC. Add a node for it.
> > >
> > > Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
> > > ---
> > >
> > > .../dts/allwinner/sun50i-h6-tanix-tx6.dts | 20 +++++++++++++++++++
> > > 1 file changed, 20 insertions(+)
> > >
> > > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-tanix-tx6.dts
> > > b/arch/arm64/boot/dts/allwinner/sun50i-h6-tanix-tx6.dts index
> > > 83e6cb0e59ce..8cbf4e4a761e 100644
> > > --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-tanix-tx6.dts
> > > +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-tanix-tx6.dts
> > > @@ -31,6 +31,13 @@ hdmi_con_in: endpoint {
> > >
> > > };
> > >
> > > };
> > >
> > > + reg_vcc1v8: vcc1v8 {
> > > + compatible = "regulator-fixed";
> > > + regulator-name = "vcc1v8";
> > > + regulator-min-microvolt = <1800000>;
> > > + regulator-max-microvolt = <1800000>;
> > > + };
> > > +
> > >
> > > reg_vcc3v3: vcc3v3 {
> > >
> > > compatible = "regulator-fixed";
> > > regulator-name = "vcc3v3";
> > >
> > > @@ -78,6 +85,15 @@ &mmc0 {
> > >
> > > status = "okay";
> > >
> > > };
> > >
> > > +&mmc2 {
> > > + vmmc-supply = <&reg_vcc3v3>;
> > > + vqmmc-supply = <&reg_vcc1v8>;
> > > + non-removable;
> > > + cap-mmc-hw-reset;
> > > + bus-width = <8>;
> > > + status = "okay";
> > > +};
> > > +
> > >
> > > &ohci0 {
> > >
> > > status = "okay";
> > >
> > > };
> > >
> > > @@ -86,6 +102,10 @@ &ohci3 {
> > >
> > > status = "okay";
> > >
> > > };
> > >
> > > +&pio {
> > > + vcc-pc-supply = <&reg_vcc1v8>;
> > > +};
> > > +
> >
> > Can you list all of the regulators for the H6 while you're at it (in a
> > preliminary patch, ideally)?
>
> Not sure what you mean. This box has only fixed regulators. I deducted above
> from the fact that port C is mostly dedicated to eMMC, so it has to use same
> regulator as vqmmc. Other than that, I don't know.

If you don't really know, then setting all of them to 3.3v makes the
most sense. It should be described anyway.

Maxime
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2020-01-22 18:42    [W:0.041 / U:0.140 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site