lkml.org 
[lkml]   [2019]   [Sep]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2 2/3] mtd: spi-nor: cadence-quadspi: disable DMA and DAC for Intel LGM
From
Date
Hi Vignesh,

Thank you so much for the review comments and your time.

On 9/9/2019 2:05 PM, Vignesh Raghavendra wrote:
> Hi,
>
> On 27/08/19 9:28 AM, Ramuthevar,Vadivel MuruganX wrote:
>> From: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
>>
>> on Intel's Lightning Mountain(LGM) SoCs QSPI controller do not use
>> Direct Memory Access(DMA) and Direct Access Controller(DAC).
>>
>> This patch introduces to properly disable the DMA and DAC
>> for data transfer instead it uses indirect data transfer.
>>
>> Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
>> ---
>> drivers/mtd/spi-nor/Kconfig | 2 +-
>> drivers/mtd/spi-nor/cadence-quadspi.c | 21 ++++++++++++++++++---
>> 2 files changed, 19 insertions(+), 4 deletions(-)
>>
>> diff --git a/drivers/mtd/spi-nor/Kconfig b/drivers/mtd/spi-nor/Kconfig
>> index 6de83277ce8b..ba2e372ae514 100644
>> --- a/drivers/mtd/spi-nor/Kconfig
>> +++ b/drivers/mtd/spi-nor/Kconfig
>> @@ -34,7 +34,7 @@ config SPI_ASPEED_SMC
>>
>> config SPI_CADENCE_QUADSPI
>> tristate "Cadence Quad SPI controller"
>> - depends on OF && (ARM || ARM64 || COMPILE_TEST)
>> + depends on OF && (ARM || ARM64 || COMPILE_TEST || X86)
>> help
>> Enable support for the Cadence Quad SPI Flash controller.
>>
>> diff --git a/drivers/mtd/spi-nor/cadence-quadspi.c b/drivers/mtd/spi-nor/cadence-quadspi.c
>> index 67f15a1f16fd..69fa13e95110 100644
>> --- a/drivers/mtd/spi-nor/cadence-quadspi.c
>> +++ b/drivers/mtd/spi-nor/cadence-quadspi.c
>> @@ -517,12 +517,16 @@ static int cqspi_indirect_read_execute(struct spi_nor *nor, u8 *rxbuf,
>> struct cqspi_st *cqspi = f_pdata->cqspi;
>> void __iomem *reg_base = cqspi->iobase;
>> void __iomem *ahb_base = cqspi->ahb_base;
>> + u32 trigger_address = cqspi->trigger_address;
>> unsigned int remaining = n_rx;
>> unsigned int mod_bytes = n_rx % 4;
>> unsigned int bytes_to_read = 0;
>> u8 *rxbuf_end = rxbuf + n_rx;
>> int ret = 0;
>>
>> + if (!f_pdata->use_direct_mode)
>> + writel(trigger_address, reg_base + CQSPI_REG_INDIRECTTRIGGER);
>> +
> Again, as I pointed out previously, this should not be needed.
> cqspi_controller_init() already does above configuration and no need to
> touch this register on every read.
Agreed!, drop this one.
>> writel(from_addr, reg_base + CQSPI_REG_INDIRECTRDSTARTADDR);
>> writel(remaining, reg_base + CQSPI_REG_INDIRECTRDBYTES);
>>
>> @@ -609,6 +613,14 @@ static int cqspi_write_setup(struct spi_nor *nor)
>> struct cqspi_st *cqspi = f_pdata->cqspi;
>> void __iomem *reg_base = cqspi->iobase;
>>
>> + /* Disable the DMA and direct access controller */
>> + if (!f_pdata->use_direct_mode) {
>> + reg = readl(reg_base + CQSPI_REG_CONFIG);
>> + reg &= ~CQSPI_REG_CONFIG_ENB_DIR_ACC_CTRL;
>> + reg &= ~CQSPI_REG_CONFIG_DMA_MASK;
>> + writel(reg, reg_base + CQSPI_REG_CONFIG);
>> + }
>> +
> You did not respond to my previous comment. Why would you need to clear
> CQSPI_REG_CONFIG_DMA_MASK field, if reset default is 0 anyway?
while testing on the real setup it is not working for me, double confirm
and drop it.
>> /* Set opcode. */
>> reg = nor->program_opcode << CQSPI_REG_WR_INSTR_OPCODE_LSB;
>> writel(reg, reg_base + CQSPI_REG_WR_INSTR);
>> @@ -1171,7 +1183,8 @@ static int cqspi_of_get_pdata(struct platform_device *pdev)
>> return -ENXIO;
>> }
>>
>> - cqspi->rclk_en = of_property_read_bool(np, "cdns,rclk-en");
>> + if (!of_device_is_compatible(np, "intel,lgm-qspi"))
>> + cqspi->rclk_en = of_property_read_bool(np, "cdns,rclk-en");
>>
> If you don't want to use this property, then just drop it from your DT.
> Don't override it in the driver based on compatible.
Sure.
>> return 0;
>> }
>> @@ -1301,7 +1314,8 @@ static int cqspi_setup_flash(struct cqspi_st *cqspi, struct device_node *np)
>> f_pdata->registered = true;
>>
>> if (mtd->size <= cqspi->ahb_size) {
>> - f_pdata->use_direct_mode = true;
>> + f_pdata->use_direct_mode =
>> + !(of_device_is_compatible(np, "intel,lgm-qspi"));
> Looks like, you haven't followed any of my advice. Please add a quirk
> flag to disable DAC mode. Something like:

Sorry,  on real setup kernel got crash if we add quirks, so that is the
reason I started using DT compatible to

avoid crashing and also don't want disturb the existing functionalities.

Let me check once again.

Thank you so much for your valuable comments.

> #define CQSPI_DISABLE_DAC_MODE BIT(1)
>
> static const struct cqspi_driver_platdata intel_lgm_qspi = {
> .hwcaps_mask = CQSPI_BASE_HWCAPS_MASK,
> .quirks = CQSPI_DISABLE_DAC_MODE,
> };
>
> static const struct of_device_id cqspi_dt_ids[] = {
>
> ...
>
> {
> .compatible = "intel,lgm-qspi",
> .data = &intel_lgm_qspi,
> },
>
> ...
> };
>
>
> Then in cqspi_setup_flash(),
>
> if (mtd->size <= cqspi->ahb_size &&
> !ddata->quirks & CQSPI_DISABLE_DAC_MODE) {
> f_pdata->use_direct_mode = true;
> ...
> }
>
>
>> dev_dbg(nor->dev, "using direct mode for %s\n",
>> mtd->name);
>>
>> @@ -1347,7 +1361,7 @@ static int cqspi_probe(struct platform_device *pdev)
>> }
>>
>> /* Obtain QSPI clock. */
>> - cqspi->clk = devm_clk_get(dev, NULL);
>> + cqspi->clk = devm_clk_get(dev, "qspi");
> This will break DT backward compatibility. Existing DTs don't have
> clock-names = "qspi". Hence, this code will error out.
> What I meant in the previous mail was: if device does not have multiple
> clk inputs then there is no need for clock-names and there is no need to
> touch this part of code.
>
> cqspi->clk = devm_clk_get(dev, NULL);
>
> This should just work fine even on your board. So drop this hunk.
Sure, I will drop it.
>> if (IS_ERR(cqspi->clk)) {
>> dev_err(dev, "Cannot claim QSPI clock.\n");
>> return PTR_ERR(cqspi->clk);
>> @@ -1369,6 +1383,7 @@ static int cqspi_probe(struct platform_device *pdev)
>> return PTR_ERR(cqspi->ahb_base);
>> }
>> cqspi->mmap_phys_base = (dma_addr_t)res_ahb->start;
>> + cqspi->trigger_address = res_ahb->start;
> Nope, this is not needed. See:
> https://elixir.bootlin.com/linux/v5.3-rc6/source/drivers/mtd/spi-nor/cadence-quadspi.c#L1168
>
> Populate the trigger-address using cdns,trigger-address property in DT

Agreed!,  fix it in the next version.

Best Regards
vadivel
>> cqspi->ahb_size = resource_size(res_ahb);
>>
>> init_completion(&cqspi->transfer_complete);
>>

\
 
 \ /
  Last update: 2019-09-09 09:33    [W:0.053 / U:0.364 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site