lkml.org 
[lkml]   [2019]   [Sep]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 2/9] crypto: Add Allwinner sun8i-ce Crypto Engine
On Sat, Sep 07, 2019 at 09:04:08PM +0200, Corentin Labbe wrote:
> > Also, I'm not sure what is the point of having the clocks names be
> > parameters there as well. It's constant across all the compatibles,
> > the only thing that isn't is the number of clocks and the module clock
> > rate. It's what you should have in there.
>
> Since the datasheet give some max frequency, I think I will add a
> max_freq and add a check to verify if the clock is in the right
> range

It's a bit pointless. What are you going to do if it's not correct?
What are you trying to fix / report with this?

> > > + }
> > > +};
> > > +
> > > +static const struct ce_variant ce_h5_variant = {
> > > + .alg_cipher = { CE_ID_NOTSUPP, CE_ALG_AES, CE_ALG_DES, CE_ALG_3DES,
> > > + CE_ID_NOTSUPP,
> > > + },
> > > + .op_mode = { CE_ID_NOTSUPP, CE_OP_ECB, CE_OP_CBC
> > > + },
> > > + .intreg = CE_ISR,
> > > + .maxflow = 4,
> > > + .ce_clks = {
> > > + { "ahb", 200000000 },
> > > + { "mod", 300000000 },
> > > + }
> > > +};
> > > +
> > > +static const struct ce_variant ce_h6_variant = {
> > > + .alg_cipher = { CE_ID_NOTSUPP, CE_ALG_AES, CE_ALG_DES, CE_ALG_3DES,
> > > + CE_ALG_RAES,
> > > + },
> > > + .op_mode = { CE_ID_NOTSUPP, CE_OP_ECB, CE_OP_CBC
> > > + },
> > > + .model = CE_v2,
> >
> > Can't that be derived from the version register and / or the
> > compatible? This seems to be redundant with each.
>
> I could use the compatible, but I want to avoid a string comparison
> on each request.

Well, this is specifically what this structure is for then, right? So
instead of having the model, just add the information that you want
there.

> > > +int sun8i_ce_get_engine_number(struct sun8i_ce_dev *ce)
> > > +{
> > > + return atomic_inc_return(&ce->flow) % ce->variant->maxflow;
> > > +}
> >
> > I'm not sure what this is supposed to be doing, but that mod there
> > seems pretty dangerous.
> >
> > ...
>
> This mod do a round robin on each channel.
> I dont see why it is dangerous.

Well, you're using the atomic API here which is most commonly used for
refcounting, while you're using a mod.

Plus, while the increment is atomic, the modulo isn't, so you can end
up in a case where you would be preempted between the
atomic_inc_return and the mod, which is dangerous.

Again, I'm not sure what this function is doing (which is also a
problem in itself). I guess you should just make it clearer what it
does, and then we can discuss it properly.

> > > + err = clk_set_rate(ce->ceclks[i], ce->variant->ce_clks[i].freq);
> > > + if (err)
> > > + dev_err(&pdev->dev, "Fail to set %s clk speed to %lu\n",
> > > + ce->variant->ce_clks[i].name,
> > > + ce->variant->ce_clks[i].freq);
> > > + } else {
> > > + dev_info(&pdev->dev, "%s run at %lu\n",
> > > + ce->variant->ce_clks[i].name, cr);
> >
> > Ditto.
> >
> > > + }
> > > + err = clk_prepare_enable(ce->ceclks[i]);
> >
> > Do you really need this right now though?
>
> Not sure to understand, why I shouldnt do it now ?
> Does it is related to your pm_runtime remark below ?
>
> My feeling was to submit the driver without PM and convert it after.

runtime_pm would be pretty cheap to add though judging by what you're
doing there.

> > > + if (err) {
> > > + dev_err(&pdev->dev, "Cannot prepare_enable %s\n",
> > > + ce->variant->ce_clks[i].name);
> > > + return err;
> > > + }
> > > + }
> > > +
> > > + /* Get Non Secure IRQ */
> > > + irq = platform_get_irq(pdev, 0);
> > > + if (irq < 0) {
> > > + dev_err(ce->dev, "Cannot get NS IRQ\n");
> > > + return irq;
> > > + }
> > > +
> > > + err = devm_request_irq(&pdev->dev, irq, ce_irq_handler, 0,
> > > + "sun8i-ce-ns", ce);
> > > + if (err < 0) {
> > > + dev_err(ce->dev, "Cannot request NS IRQ\n");
> > > + return err;
> > > + }
> > > +
> > > + ce->reset = devm_reset_control_get_optional(&pdev->dev, "ahb");
> > > + if (IS_ERR(ce->reset)) {
> > > + if (PTR_ERR(ce->reset) == -EPROBE_DEFER)
> > > + return PTR_ERR(ce->reset);
> > > + dev_info(&pdev->dev, "No reset control found\n");
> >
> > It's not optional though.
>
> I dont understand why.

On all the SoCs, you need that reset line to be deasserted, otherwise
the IP (and therefore the driver) will be non-functional. It's not an
option to run without it.

> > > + ce->reset = NULL;
> > > + }
> > > +
> > > + err = reset_control_deassert(ce->reset);
> > > + if (err) {
> > > + dev_err(&pdev->dev, "Cannot deassert reset control\n");
> > > + goto error_clk;
> > > + }
> >
> > Again, you don't really need this at this moment. Using runtime_pm
> > would make more sense.
> >
> > > + v = readl(ce->base + CE_CTR);
> > > + v >>= 16;
> > > + v &= 0x07;
> >
> > This should be in a define
> >
>
> Will fix.
>
> > > + dev_info(&pdev->dev, "CE_NS Die ID %x\n", v);
> >
> > And if that really makes sense to print it, the error message should
> > be made less cryptic.
> >
>
> Will fix.
>
> > > +
> > > + ce->dev = &pdev->dev;
> > > + platform_set_drvdata(pdev, ce);
> > > +
> > > + mutex_init(&ce->mlock);
> > > +
> > > + ce->chanlist = devm_kcalloc(ce->dev, ce->variant->maxflow,
> > > + sizeof(struct sun8i_ce_flow), GFP_KERNEL);
> > > + if (!ce->chanlist) {
> > > + err = -ENOMEM;
> > > + goto error_flow;
> > > + }
> > > +
> > > + for (i = 0; i < ce->variant->maxflow; i++) {
> > > + init_completion(&ce->chanlist[i].complete);
> > > + mutex_init(&ce->chanlist[i].lock);
> > > +
> > > + ce->chanlist[i].engine = crypto_engine_alloc_init(ce->dev, true);
> > > + if (!ce->chanlist[i].engine) {
> > > + dev_err(ce->dev, "Cannot allocate engine\n");
> > > + i--;
> > > + goto error_engine;
> > > + }
> > > + err = crypto_engine_start(ce->chanlist[i].engine);
> > > + if (err) {
> > > + dev_err(ce->dev, "Cannot start engine\n");
> > > + goto error_engine;
> > > + }
> > > + ce->chanlist[i].tl = dma_alloc_coherent(ce->dev,
> > > + sizeof(struct ce_task),
> > > + &ce->chanlist[i].t_phy,
> > > + GFP_KERNEL);
> > > + if (!ce->chanlist[i].tl) {
> > > + dev_err(ce->dev, "Cannot get DMA memory for task %d\n",
> > > + i);
> > > + err = -ENOMEM;
> > > + goto error_engine;
> > > + }
> > > + }
> >
> > All this initialization should be done before calling
> > request_irq. You're using some of those fields in your handler.
>
> No interrupt could fire, since algorithms are still not registred.

That's not true. Spurious interrupts are a thing, the engine could
have been left in a weird state by the bootloader / kexec / reboot
with some pending interrupts, etc.

You have registered that handler already, you should expect it to be
called at any point in time.

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

\
 
 \ /
  Last update: 2019-09-09 13:39    [W:0.083 / U:0.220 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site