lkml.org 
[lkml]   [2019]   [Sep]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH v3 1/2] ethtool: implement Energy Detect Powerdown support via phy-tunable
Date
On Tue, 2019-09-10 at 10:00 +0200, Michal Kubecek wrote:
> [External]
>
> On Mon, Sep 09, 2019 at 04:12:50PM +0300, Alexandru Ardelean wrote:
> > The `phy_tunable_id` has been named `ETHTOOL_PHY_EDPD` since it looks like
> > this feature is common across other PHYs (like EEE), and defining
> > `ETHTOOL_PHY_ENERGY_DETECT_POWER_DOWN` seems too long.
> >
> > The way EDPD works, is that the RX block is put to a lower power mode,
> > except for link-pulse detection circuits. The TX block is also put to low
> > power mode, but the PHY wakes-up periodically to send link pulses, to avoid
> > lock-ups in case the other side is also in EDPD mode.
> >
> > Currently, there are 2 PHY drivers that look like they could use this new
> > PHY tunable feature: the `adin` && `micrel` PHYs.
> >
> > The ADIN's datasheet mentions that TX pulses are at intervals of 1 second
> > default each, and they can be disabled. For the Micrel KSZ9031 PHY, the
> > datasheet does not mention whether they can be disabled, but mentions that
> > they can modified.
> >
> > The way this change is structured, is similar to the PHY tunable downshift
> > control:
> > * a `ETHTOOL_PHY_EDPD_DFLT_TX_INTERVAL` value is exposed to cover a default
> > TX interval; some PHYs could specify a certain value that makes sense
> > * `ETHTOOL_PHY_EDPD_NO_TX` would disable TX when EDPD is enabled
> > * `ETHTOOL_PHY_EDPD_DISABLE` will disable EDPD
> >
> > This should allow PHYs to:
> > * enable EDPD and not enable TX pulses (interval would be 0)
> > * enable EDPD and configure TX pulse interval; note that TX interval units
> > would be PHY specific; we could consider `seconds` as units, but it could
> > happen that some PHYs would be prefer milliseconds as a unit;
> > a maximum of 65533 units should be sufficient
>
> Sorry for missing the discussion on previous version but I don't really
> like the idea of leaving the choice of units to PHY. Both for manual
> setting and system configuration, it would be IMHO much more convenient
> to have the interpretation universal for all NICs.
>

I was also a bit uncertain/undecided here about letting PHYs decide units.
And I also wasn't sure what to propose.
Not proposing a unit now, would have allowed us to decide later based on what PHYs implement (generally) in the future.
I know that may make me look a bit lazy [for not proposing units in ethtool], but tbh it's more of lack-of-experience
with ethtool (or these APIs) evolve over time.

> Seconds as units seem too coarse and maximum of ~18 hours way too big.
> Milliseconds would be more practical from granularity point of view,
> would maximum of ~65 seconds be sufficient?

I think 65 seconds is more than enough.
I feel that, if you plug-in an eth cable and don't have a link in a minute, then it's not great (no matter how much of a
power-saver you are).

Actually, voicing out these units makes it simpler for a decision to go in favor for milliseconds.
So: thank you :)

Alex

>
> Michal Kubecek
>
> > * disable EDPD
> >
> > Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
\
 
 \ /
  Last update: 2019-09-10 14:08    [W:0.040 / U:0.308 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site