lkml.org 
[lkml]   [2019]   [Aug]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: iio: Is storing output values to non volatile registers something we should do automatically or leave to userspace action. [was Re: [PATCH] iio: potentiometer: max5432: update the non-volatile position]
On Mon, 12 Aug 2019 19:08:12 +0800
Phil Reid <preid@electromag.com.au> wrote:

> G'day Martin / Jonathan,
>
> On 12/08/2019 18:37, Martin Kaiser wrote:
> > Hi Jonathan,
> >
> > Thus wrote Jonathan Cameron (jic23@kernel.org):
> >
> >> The patch is fine, but I'm wondering about whether we need some element
> >> of policy control on this restore to current value.
> >
> >> A few things to take into account.
> >
> >> * Some devices don't have a non volatile store. So userspace will be
> >> responsible for doing the restore on reboot.
> >> * This may be one of several related devices, and it may make no sense
> >> to restore this one if the others aren't going to be in the same
> >> state as before the reboot.
> >> * Some devices only have non volatile registers for this sort of value
> >> (or save to non volatile on removal of power). Hence any policy to
> >> not store the value can't apply to this class of device.
> >
> > I see your point. You'd like a consistent bahaviour across all
> > potentiometer drivers. Or at least a way for user space to figure out
> > whether a chip uses non-volatile storage or not.
> > This property doesn't quite fit into the channel info that are defined
> > in the arrays in drivers/iio/industrialio-core.c. Is there any other way
> > to set such a property?
> >
> >> My initial thought is that these probably don't matter that much and
> >> we should apply this, but I would like to seek input from others!
> >
> >> I thought there were some other drivers doing similar store to no
> >> volatile but I can't find one.
> >
> > drivers/iio/potentiometer/max5481.c and max5487.c do something similar.
> >
> > They use a command to transfer the setting from volatile to non-volatile
> > register in the spi remove function. I guess that the intention is to
> > save the current setting when the system is rebooted. However, my
> > understanding is that the remove function is called only when a module
> > is unloaded or when user space does explicitly unbind the device from
> > the bus via sysfs. That's why I tried using the shutdown function
> > instead.
> >
> > Still, this approach has some disadvantages. For many systems, there's a
> > soft reboot (shutdown -r) where the driver's shutdown function is called
> > and a "hard reboot" where the power from the CPU and the potentiometer
> > chip is removed and reapplied. In this case, the current value would not
> > be transfered to the non-volatile register.
> >
> > At least for the max5432 family, there's no way to read the current
> > setting. The only option for user space to have a well-defined setting
> > is to set the wiper position explicitly at startup.
> >
> > I guess the only sensible way to use a non-volatile register would be a
> > write operation where user space gets a response about successful
> > completion.
> >
> > We could have two channels to write to the volatile or to non-volatile
> > register. Or we stick to one channel and update both volatile and
> > non-volatile registers when user space changes the value. This assumes
> > that the setting does not change frequently, which is prabably not true
> > for all applications...

I'm not keen on multiple channels as that is a fairly non obvious interface.
Definitely want to avoid writing all the time.

> >
> > Whatever we come up with, we should at least make the max* chips behave
> > the same way.
> >
> The AD5272/AD5274 Digital Rheostat has a 50-times limit for programming the NV register.
> So you want to be real sure that you want to set it.

Ouch, I new some were limited to a few thousand cycles, but 50 is rather nasty!

>
> I'd rather my system default to a known "safe" value for next boot than
> set to whatever the last write was. So some kind of policy on setting this would
> be nice. I personally think it's something that userspace should initiate via an explicit
> command.
Agreed. I think we should look at an explicit write.

Perhaps an extra attribute on the channels? Hence a shared_by_all version
could be used when there is only one write command.

>
> Writing the NV for the AD5272 is something I planned to add at some stage.
> But so far the default factory values have worked ok.
> It'd be nice for cross device consistency for any interface for this.
>
Agreed. This is an area that crept up on me, so we haven't enforced any
consistency on it yet. However, we definitely should!

Thanks,

Jonathan

\
 
 \ /
  Last update: 2019-08-18 21:34    [W:0.043 / U:1.056 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site