lkml.org 
[lkml]   [2019]   [Aug]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH] ACPI: PM: Fix regression in acpi_device_set_power()
Date
> -----Original Message-----
> From: Kai-Heng Feng <kai.heng.feng@canonical.com>
> Sent: Thursday, August 1, 2019 1:11 AM
> To: Rafael J. Wysocki
> Cc: Linux ACPI; Linux PM; Linux PCI; LKML; Mika Westerberg; Bjorn Helgaas;
> Limonciello, Mario
> Subject: Re: [PATCH] ACPI: PM: Fix regression in acpi_device_set_power()
>
>
> at 07:31, Rafael J. Wysocki <rjw@rjwysocki.net> wrote:
>
> > From: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
> >
> > Commit f850a48a0799 ("ACPI: PM: Allow transitions to D0 to occur in
> > special cases") overlooked the fact that acpi_power_transition() may
> > change the power.state value for the target device and if that
> > happens, it may confuse acpi_device_set_power() and cause it to
> > omit the _PS0 evaluation which on some systems is necessary to
> > change power states of devices from low-power to D0.
> >
> > Fix that by saving the current value of power.state for the
> > target device before passing it to acpi_power_transition() and
> > using the saved value in a subsequent check.
> >
> > Fixes: f850a48a0799 ("ACPI: PM: Allow transitions to D0 to occur in
> > special cases")
> > Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
> > Reported-by: Mario Limonciello <mario.limonciello@dell.com>
> > Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
>
> Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>

Tested-by: Mario Limonciello <mario.limonciello@dell.com>

>
> > ---
> > drivers/acpi/device_pm.c | 4 +++-
> > 1 file changed, 3 insertions(+), 1 deletion(-)
> >
> > Index: linux-pm/drivers/acpi/device_pm.c
> >
> ==============================================================
> =====
> > --- linux-pm.orig/drivers/acpi/device_pm.c
> > +++ linux-pm/drivers/acpi/device_pm.c
> > @@ -236,13 +236,15 @@ int acpi_device_set_power(struct acpi_de
> > if (device->power.flags.power_resources)
> > result = acpi_power_transition(device, target_state);
> > } else {
> > + int cur_state = device->power.state;
> > +
> > if (device->power.flags.power_resources) {
> > result = acpi_power_transition(device, ACPI_STATE_D0);
> > if (result)
> > goto end;
> > }
> >
> > - if (device->power.state == ACPI_STATE_D0) {
> > + if (cur_state == ACPI_STATE_D0) {
> > int psc;
> >
> > /* Nothing to do here if _PSC is not present. */
>

\
 
 \ /
  Last update: 2019-08-01 21:07    [W:0.115 / U:0.180 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site