lkml.org 
[lkml]   [2019]   [Jul]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [alsa-devel] [PATCH 05/10] ASoC: fsl_sai: Add support to enable multiple data lines
On Mon, Jul 22, 2019 at 3:58 PM Lucas Stach <l.stach@pengutronix.de> wrote:
>
> Am Montag, den 22.07.2019, 15:48 +0300 schrieb Daniel Baluta:
> > SAI supports up to 8 Rx/Tx data lines which can be enabled
> > using TCE/RCE bits of TCR3/RCR3 registers.
> >
> > Data lines to be enabled are read from DT fsl,dl_mask property.
> > By default (if no DT entry is provided) only data line 0 is enabled.
> >
> > Note:
> > We can only enable consecutive data lines starting with data line #0.
>
> Why is the property a bitmask then? To me this sounds like we want to
> have the number of lanes in the DT and convert to the bitmask inside
> the driver.

Actually my comment might be wrong. I have read the documentation again
and it seems that: We can only enable consecutive data lines
*ONLY* if combine mode is enabled.

Thus, if combine mode is disabled we can independently enable any data
line. I will clarify this with IP owner and correct the patch accordingly.

>
> > > Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
> > ---
> > sound/soc/fsl/fsl_sai.c | 10 +++++++++-
> > sound/soc/fsl/fsl_sai.h | 6 ++++--
> > 2 files changed, 13 insertions(+), 3 deletions(-)
> >
> > diff --git a/sound/soc/fsl/fsl_sai.c b/sound/soc/fsl/fsl_sai.c
> > index 768341608695..d0fa02188b7c 100644
> > --- a/sound/soc/fsl/fsl_sai.c
> > +++ b/sound/soc/fsl/fsl_sai.c
> > @@ -601,7 +601,7 @@ static int fsl_sai_startup(struct snd_pcm_substream *substream,
> >
> > > regmap_update_bits(sai->regmap, FSL_SAI_xCR3(tx),
> > > FSL_SAI_CR3_TRCE_MASK,
> > > - FSL_SAI_CR3_TRCE);
> > > + FSL_SAI_CR3_TRCE(sai->soc_data->dl_mask[tx]);
> >
> > > ret = snd_pcm_hw_constraint_list(substream->runtime, 0,
> > > SNDRV_PCM_HW_PARAM_RATE, &fsl_sai_rate_constraints);
> > @@ -887,6 +887,14 @@ static int fsl_sai_probe(struct platform_device *pdev)
> > > }
> > > }
> >
> > > + /* active data lines mask for TX/RX, defaults to 1 (only the first
> > > + * data line is enabled
> > + */
>
> Comment style not in line with Linux coding style.

Will fix. Thanks Lucas for review.
Should be like this, right?
/*
* comment
*/

checkpatch.pl warned me only about the end of the comment :).

\
 
 \ /
  Last update: 2019-07-24 10:58    [W:0.031 / U:1.548 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site