lkml.org 
[lkml]   [2019]   [Jul]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v4 03/24] PM / devfreq: tegra30: Handle possible round-rate error
From
Date
On 19. 7. 16. 오후 10:09, Dmitry Osipenko wrote:
> 16.07.2019 14:50, Chanwoo Choi пишет:
>> On 19. 7. 8. 오전 7:32, Dmitry Osipenko wrote:
>>> The EMC clock rate rounding technically could fail, hence let's handle
>>> the error cases properly.
>>>
>>> Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
>>> ---
>>> drivers/devfreq/tegra30-devfreq.c | 17 +++++++++++++++--
>>> 1 file changed, 15 insertions(+), 2 deletions(-)
>>>
>>> diff --git a/drivers/devfreq/tegra30-devfreq.c b/drivers/devfreq/tegra30-devfreq.c
>>> index 5e2b133babdd..5e606ae3f238 100644
>>> --- a/drivers/devfreq/tegra30-devfreq.c
>>> +++ b/drivers/devfreq/tegra30-devfreq.c
>>> @@ -592,8 +592,8 @@ static int tegra_devfreq_probe(struct platform_device *pdev)
>>> struct tegra_devfreq_device *dev;
>>> struct tegra_devfreq *tegra;
>>> struct devfreq *devfreq;
>>> - unsigned long rate;
>>> unsigned int i;
>>> + long rate;
>>> int err;
>>>
>>> tegra = devm_kzalloc(&pdev->dev, sizeof(*tegra), GFP_KERNEL);
>>> @@ -650,8 +650,14 @@ static int tegra_devfreq_probe(struct platform_device *pdev)
>>>
>>> reset_control_deassert(tegra->reset);
>>>
>>> - tegra->max_freq = clk_round_rate(tegra->emc_clock, ULONG_MAX) / KHZ;
>>> + rate = clk_round_rate(tegra->emc_clock, ULONG_MAX);
>>> + if (rate < 0) {
>>> + dev_err(&pdev->dev, "Failed to round clock rate: %ld\n", rate);
>>> + return rate;
>>> + }
>>> +
>>> tegra->cur_freq = clk_get_rate(tegra->emc_clock) / KHZ;
>>> + tegra->max_freq = rate / KHZ;
>>>
>>> for (i = 0; i < ARRAY_SIZE(actmon_device_configs); i++) {
>>> dev = tegra->devices + i;
>>> @@ -662,6 +668,13 @@ static int tegra_devfreq_probe(struct platform_device *pdev)
>>> for (rate = 0; rate <= tegra->max_freq * KHZ; rate++) {
>>> rate = clk_round_rate(tegra->emc_clock, rate);
>>>
>>
>> Please remove unneeded blank line.
>
> I can remove it, but it was added specifically to ease reading of the code.
>
>>> + if (rate < 0) {
>>> + dev_err(&pdev->dev,
>>> + "Failed to round clock rate: %ld\n", rate);
>>> + err = rate;
>>> + goto remove_opps;
>>> + }
>>
>> Also, this patch doesn't contain code which restore the previous
>> tegra->cur_freq/max_freq when error happen.
>
> The error here results in abortion of the driver's probing, hence
> nothing need to be restored in that case because nothing was changed at
> this point yet.
>
>

OK.


--
Best Regards,
Chanwoo Choi
Samsung Electronics

\
 
 \ /
  Last update: 2019-07-17 08:36    [W:0.159 / U:0.556 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site