lkml.org 
[lkml]   [2019]   [Jun]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v4 7/7] s390: vfio-ap: update documentation
From
Date
On 6/17/19 7:42 AM, Harald Freudenberger wrote:
> On 13.06.19 21:39, Tony Krowiak wrote:
>> This patch updates the vfio-ap documentation to include the information
>> below.
>>
>> Changes made to the mdev matrix assignment interfaces:
>>
>> * Allow assignment of APQNs that are not bound to the vfio-ap device
>> driver as long as they are not owned by a zcrypt driver as identified
>> in the AP bus sysfs apmask and aqmask interfaces.
>>
>> * Allow assignment of an AP resource to a mediated device which is in use
>> by a guest to hot plug an adapter, domain and control domain into a
>> running guest.
>>
>> * Allow unassignment of an AP resource from a mediated device which is in
>> use by a guest to hot unplug an adapter, domain and control domain from
>> a running guest.
>>
>> This patch also:
>>
>> * Clarifies the section on configuring the AP bus's apmask and aqmask.
>>
>> * Adds sections on dynamic configuration using the SE or SCLP command.
>>
>> Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
>> ---
>> Documentation/s390/vfio-ap.txt | 292 ++++++++++++++++++++++++++++++-----------
>> 1 file changed, 213 insertions(+), 79 deletions(-)
>>
>> diff --git a/Documentation/s390/vfio-ap.txt b/Documentation/s390/vfio-ap.txt
>> index 65167cfe4485..9372a6570ce1 100644
>> --- a/Documentation/s390/vfio-ap.txt
>> +++ b/Documentation/s390/vfio-ap.txt
>> @@ -81,10 +81,19 @@ definitions:
>> which the AP command is to be sent for processing.
>>
>> The AP bus will create a sysfs device for each APQN that can be derived from
>> - the cross product of the AP adapter and usage domain numbers detected when the
>> - AP bus module is loaded. For example, if adapters 4 and 10 (0x0a) and usage
>> - domains 6 and 71 (0x47) are assigned to the LPAR, the AP bus will create the
>> - following sysfs entries:
>> + the Cartesian product of the AP adapter and usage domain numbers detected when
>> + the AP bus module is loaded. For example, if adapters 4 and 10 (0x0a) and
>> + usage domains 6 and 71 (0x47) are assigned to the LPAR, the Cartesian product
>> + would be defined by the following table:
>> +
>> + 06 71
>> + +-----------+-----------+
>> + 04 | (04,06) | (04,47) |
>> + +-----------|-----------+
>> + 10 | (0a,06) | (0a,47) |
>> + +-----------|-----------+
>> +
> These ascii pictures are nice and show very lovely how this works ...
> but you use the domain id as column (x) and the adapter id as row (y).
> Then the APQNs are shown in (y,x) writing then following the scheme
> (card,domain).

I'll fix this.

>> + The AP bus will create the following sysfs entries:
>>
>> /sys/devices/ap/card04/04.0006
>> /sys/devices/ap/card04/04.0047
>> @@ -146,10 +155,20 @@ If you recall from the description of an AP Queue, AP instructions include
>> an APQN to identify the AP queue to which an AP command-request message is to be
>> sent (NQAP and PQAP instructions), or from which a command-reply message is to
>> be received (DQAP instruction). The validity of an APQN is defined by the matrix
>> -calculated from the APM and AQM; it is the cross product of all assigned adapter
>> -numbers (APM) with all assigned queue indexes (AQM). For example, if adapters 1
>> -and 2 and usage domains 5 and 6 are assigned to a guest, the APQNs (1,5), (1,6),
>> -(2,5) and (2,6) will be valid for the guest.
>> +calculated from the APM and AQM; it is the Cartesian product of all assigned
>> +adapter numbers (APM) with all assigned queue indexes (AQM). For example, if
>> +adapters 1 and 2 and usage domains 5 and 6 are assigned to a guest:
>> +
>> +
>> + 05 06
>> + +-----------+-----------+
>> + 01 | (01,05) | (01,06) |
>> + +-----------|-----------+
>> + 02 | (02,05) | (02,06) |
>> + +-----------|-----------+
>> +
>> +
>> +APQNs (01,05), (01,06), (02,05) and (02,06) will be valid for the guest.
>>
>> The APQNs can provide secure key functionality - i.e., a private key is stored
>> on the adapter card for each of its domains - so each APQN must be assigned to
>> @@ -349,8 +368,9 @@ matrix device.
>> number of the the usage domain is echoed to the respective attribute
>> file.
>> * matrix:
>> - A read-only file for displaying the APQNs derived from the cross product
>> - of the adapter and domain numbers assigned to the mediated matrix device.
>> + A read-only file for displaying the APQNs derived from the Caresian
>> + product of the adapter and domain numbers assigned to the mediated matrix
>> + device.
>> * assign_control_domain:
>> * unassign_control_domain:
>> Write-only attributes for assigning/unassigning an AP control domain
>> @@ -438,9 +458,10 @@ guest use.
>> Example:
>> =======
>> Let's now provide an example to illustrate how KVM guests may be given
>> -access to AP facilities. For this example, we will show how to configure
>> -three guests such that executing the lszcrypt command on the guests would
>> -look like this:
>> +access to AP facilities. For this example, we will assume that adapters 4, 5
>> +and 6 and domains 4, 71 (0x47), 171 (0xab) and 255 (0xff) are assigned to the
>> +LPAR and are online. We will show how to configure three guests such that
>> +executing the lszcrypt command on the guests would look like this:
>>
>> Guest1
>> ------
>> @@ -466,7 +487,7 @@ Guest2
>> CARD.DOMAIN TYPE MODE
>> ------------------------------
>> 06 CEX5A Accelerator
>> -06.0047 CEX5A Accelerator
>> +06.0047 CEX5A AcceleratorNote that this directory may contain additional bindings depending upon what
> This line looks somehow weird.

Sometimes my editor does weird things like this. I'll fix it.

>> 06.00ff CEX5A Accelerator
>>
>> These are the steps:
>> @@ -513,35 +534,44 @@ These are the steps:
>> /sys/bus/ap/aqmask
>>
>> The 'apmask' is a 256-bit mask that identifies a set of AP adapter IDs
>> - (APID). Each bit in the mask, from left to right (i.e., from most significant
>> - to least significant bit in big endian order), corresponds to an APID from
>> - 0-255. If a bit is set, the APID is marked as usable only by the default AP
>> - queue device drivers; otherwise, the APID is usable by the vfio_ap
>> - device driver.
>> + (APID). Each bit in the mask, from left to right, corresponds to an APID from
>> + 0-255.
>>
>> The 'aqmask' is a 256-bit mask that identifies a set of AP queue indexes
>> - (APQI). Each bit in the mask, from left to right (i.e., from most significant
>> - to least significant bit in big endian order), corresponds to an APQI from
>> - 0-255. If a bit is set, the APQI is marked as usable only by the default AP
>> - queue device drivers; otherwise, the APQI is usable by the vfio_ap device
>> - driver.
>> + (APQI). Each bit in the mask, from left to right, corresponds to an APQI from
>> + 0-255.
>> +
>> + The Cartesian product of the APIDs set in the apmask and the APQIs set in
>> + the aqmask identify the APQNs of AP queue devices owned by the zcrypt
>> + device drivers.
>> +
>> + Take, for example, the following masks:
>>
>> - Take, for example, the following mask:
>> + apmask: 0x7000000000000000000000000000000000000000000000000000000000000000
>>
>> - 0x7dffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff
>> + aqmask: 0x0180000000000000000000000000000000000000000000000000000000000000
>>
>> - It indicates:
>> + The bits set in apmask are bits 1, 2 and 3. The bits set in aqmask are bits
>> + 7 and 8. The Cartesian product of the bits set in the two masks is:
>>
>> - 1, 2, 3, 4, 5, and 7-255 belong to the default drivers' pool, and 0 and 6
>> - belong to the vfio_ap device driver's pool.
>> + 07 08
>> + +-----------+-----------+
>> + 01 | (01,07) | (01,08) |
>> + +-----------|-----------+
>> + 02 | (02,07) | (02,08) |
>> + +-----------|-----------+
>> + 03 | (03,07) | (03,08) |
>> + +-----------|-----------+
>>
>> - The APQN of each AP queue device assigned to the linux host is checked by the
>> - AP bus against the set of APQNs derived from the cross product of APIDs
>> - and APQIs marked as usable only by the default AP queue device drivers. If a
>> - match is detected, only the default AP queue device drivers will be probed;
>> - otherwise, the vfio_ap device driver will be probed.
>> + The masks indicate that the queues with APQNs (01,07), (01,08), (02,07),
>> + (02,08), (03,07) and (03,08) are owned by the zcrypt drivers. When the AP bus
>> + detects an AP queue device, its APQN is checked against the set of APQNs
>> + derived from the apmask and aqmask. If a match is detected, the zcrypt
>> + device driver registered for the device type of the queue will be probed. If
>> + a match is not detected and the device type of the queue is CEX4 or newer,
>> + the vfio_ap device driver will be probed.
>>
>> - By default, the two masks are set to reserve all APQNs for use by the default
>> + By default, the two masks are set to reserve all APQNs for use by the zcrypt
>> AP queue device drivers. There are two ways the default masks can be changed:
>>
>> 1. The sysfs mask files can be edited by echoing a string into the
>> @@ -554,8 +584,7 @@ These are the steps:
>>
>> 0x4100000000000000000000000000000000000000000000000000000000000000
>>
>> - Keep in mind that the mask reads from left to right (i.e., most
>> - significant to least significant bit in big endian order), so the mask
>> + Keep in mind that the mask reads from left to right, so the mask
>> above identifies device numbers 1 and 7 (01000001).
>>
>> If the string is longer than the mask, the operation is terminated with
>> @@ -563,7 +592,7 @@ These are the steps:
>>
>> * Individual bits in the mask can be switched on and off by specifying
>> each bit number to be switched in a comma separated list. Each bit
>> - number string must be prepended with a ('+') or minus ('-') to indicate
>> + number string must be prefixed with a ('+') or minus ('-') to indicate
>> the corresponding bit is to be switched on ('+') or off ('-'). Some
>> valid values are:
>>
>> @@ -594,19 +623,26 @@ These are the steps:
>> aqmask:
>> 0x4000000000000000000000000000000000000000000000000000000000000000
>>
>> - Resulting in these two pools:
>> -
>> - default drivers pool: adapter 0-15, domain 1
>> - alternate drivers pool: adapter 16-255, domains 0, 2-255
>> +Recall that the Cartesian product of the APIDs set in the apmask and the APQIs
>> +set in the aqmask identify the APQNs of AP queue devices owned by the zcrypt
>> +device drivers. If an attempt is made to modify the apmask or aqmask such that
>> +one or more APQNs changes ownership from a the vfio_ap device driver to a zcrypt
>> +device driver and the APQN is assigned to a mediated device (see step 3 below),
>> +the operation will fail with an error ('Address already in use').
>>
>> Securing the APQNs for our example:
>> ----------------------------------
>> - To secure the AP queues 05.0004, 05.0047, 05.00ab, 05.00ff, 06.0004, 06.0047,
>> - 06.00ab, and 06.00ff for use by the vfio_ap device driver, the corresponding
>> - APQNs can either be removed from the default masks:
>> + There is no way to secure the specific AP queues 05.0004, 05.0047, 05.00ab,
>> + 05.00ff, 06.0004, 06.0047, 06.00ab, and 06.00ff for use by the vfio_ap device
>> + driver, so we are left with either securing all queues on adapters 05 and
>> + 06, or queues 0004, 0047, 00ab and 00ff can be secured on all adapters.
>> +
>> + To secure all queues on adapters 05 and 05:
>>
>> echo -5,-6 > /sys/bus/ap/apmask
>>
>> + To secure queues 0004, 0047, 00ab, and 00ff on all adapters:
>> +
>> echo -4,-0x47,-0xab,-0xff > /sys/bus/ap/aqmask
>>
>> Or the masks can be set as follows:
>> @@ -617,14 +653,20 @@ These are the steps:
>> echo 0xf7fffffffffffffffeffffffffffffffffffffffffeffffffffffffffffffffe \
>> > aqmask
>>
>> - This will result in AP queues 05.0004, 05.0047, 05.00ab, 05.00ff, 06.0004,
>> - 06.0047, 06.00ab, and 06.00ff getting bound to the vfio_ap device driver. The
>> - sysfs directory for the vfio_ap device driver will now contain symbolic links
>> - to the AP queue devices bound to it:
>> + For this example, we will choose to secure queues 0004, 0047, 00ab, and 00ff
>> + on all adapters. This will result in AP queues 04.0004, 04.0047, 04.00ab,
>> + 04.00ff, 05.0004, 05.0047, 05.00ab, 05.00ff, 06.0004, 06.0047, 06.00ab and
>> + 06.00ff getting bound to the vfio_ap device driver. The sysfs directory for
>> + the vfio_ap device driver will now contain symbolic links to the AP queue
>> + devices bound to it:
>>
>> /sys/bus/ap
>> ... [drivers]
>> ...... [vfio_ap]
>> + ......... [04.0004]
>> + ......... [04.0047]
>> + ......... [04.00ab]
>> + ......... [04.00ff]
>> ......... [05.0004]
>> ......... [05.0047]
>> ......... [05.00ab]
>> @@ -641,11 +683,12 @@ These are the steps:
>> future and for which there are few older systems on which to test.
>>
>> The administrator, therefore, must take care to secure only AP queues that
>> - can be bound to the vfio_ap device driver. The device type for a given AP
>> - queue device can be read from the parent card's sysfs directory. For example,
>> - to see the hardware type of the queue 05.0004:
>> + can be bound to the vfio_ap device driver, or those queues will not get bound
>> + to any driver. The device type for a given AP queue device can be read from
>> + the parent card's sysfs directory. For example, to see the hardware type of
>> + the queue 05.0004:
>>
>> - cat /sys/bus/ap/devices/card05/hwtype
>> + cat /sys/bus/ap/devices/card05/hwtype
>>
>> The hwtype must be 10 or higher (CEX4 or newer) in order to be bound to the
>> vfio_ap device driver.
>> @@ -747,37 +790,48 @@ These are the steps:
>> higher than the maximum is specified, the operation will terminate with
>> an error (ENODEV).
>>
>> - * All APQNs that can be derived from the adapter ID and the IDs of
>> - the previously assigned domains must be bound to the vfio_ap device
>> - driver. If no domains have yet been assigned, then there must be at least
>> - one APQN with the specified APID bound to the vfio_ap driver. If no such
>> - APQNs are bound to the driver, the operation will terminate with an
>> - error (EADDRNOTAVAIL).
>> + * Each APQN that can be derived from the adapter ID and the IDs of
>> + the previously assigned domains must not be reserved for use by the
>> + zcrypt device drivers as specified by the /sys/bus/ap/apmask and
>> + /sys/bus/ap/aqmask syfs interfaces. If any APQN is reserved, the operation
>> + will terminate with an error (EADDRNOTAVAIL).
>>
>> - No APQN that can be derived from the adapter ID and the IDs of the
>> + * No APQN that can be derived from the adapter ID and the IDs of the
>> previously assigned domains can be assigned to another mediated matrix
>> device. If an APQN is assigned to another mediated matrix device, the
>> operation will terminate with an error (EADDRINUSE).
>>
>> + Note that adapters that are currently not available to the host may be
>> + assigned to the mediated device. If the adapter subsequently becomes
>> + available while a guest is using the mediated device, it will automatically
>> + become available to the guest.
>> +
>> In order to successfully assign a domain:
>>
>> * The domain number specified must represent a value from 0 up to the
>> maximum domain number configured for the system. If a domain number
>> higher than the maximum is specified, the operation will terminate with
>> - an error (ENODEV).
>> + an error (ENODEV). The maximum domain number can be determined by
>> + printing the sysfs /sys/bus/ap/ap_max_domain_id attribute:
>>
>> - * All APQNs that can be derived from the domain ID and the IDs of
>> - the previously assigned adapters must be bound to the vfio_ap device
>> - driver. If no domains have yet been assigned, then there must be at least
>> - one APQN with the specified APQI bound to the vfio_ap driver. If no such
>> - APQNs are bound to the driver, the operation will terminate with an
>> - error (EADDRNOTAVAIL).
>> + cat /sys/bus/ap/ap_max_domain_id
>>
>> - No APQN that can be derived from the domain ID and the IDs of the
>> + * Each APQN that can be derived from the domain ID and the IDs of
>> + the previously assigned adapters must not be reserved for use by the
>> + zcrypt device drivers as specified by the /sys/bus/ap/apmask and
>> + /sys/bus/ap/aqmask syfs interfaces. If any APQN is reserved, the operation
>> + will terminate with an error (EADDRNOTAVAIL).
>> +
>> + * No APQN that can be derived from the domain ID and the IDs of the
>> previously assigned adapters can be assigned to another mediated matrix
>> device. If an APQN is assigned to another mediated matrix device, the
>> operation will terminate with an error (EADDRINUSE).
>>
>> + Note that domains that are currently not available to the host may be
>> + assigned to the mediated device. If the domain subsequently becomes
>> + available while a guest is using the mediated device, it will automatically
>> + become available to the guest.
>> +
>> In order to successfully assign a control domain, the domain number
>> specified must represent a value from 0 up to the maximum domain number
>> configured for the system. If a control domain number higher than the maximum
>> @@ -822,16 +876,96 @@ Using our example again, to remove the mediated matrix device $uuid1:
>> host. If the mdev matrix device is removed, one may want to also reconfigure
>> the pool of adapters and queues reserved for use by the default drivers.
>>
>> -Limitations
>> -===========
>> -* The KVM/kernel interfaces do not provide a way to prevent restoring an APQN
>> - to the default drivers pool of a queue that is still assigned to a mediated
>> - device in use by a guest. It is incumbent upon the administrator to
>> - ensure there is no mediated device in use by a guest to which the APQN is
>> - assigned lest the host be given access to the private data of the AP queue
>> - device such as a private key configured specifically for the guest.
>> +Hot plug/unplug via mdev matrix device sysfs interfaces:
>> +=======================================================
>> +If an mdev matrix device is in use by a running guest, AP resources can be
>> +plugged into or unplugged from the guest via the mdev device's sysfs
>> +assignment interfaces. Below are some examples.
>> +
>> + To plug adapter 10 into a running guest:
>> +
>> + echo 0xa > assign_adapter
>> +
>> + To unplug domain 5 from a running guest:
>> +
>> + echo 5 > unassign_domain
>> +
>> +To display the matrix of a guest using the mdev matrix device:
>> +
>> + cat guest_matrix
>> +
>> +If you attempt to display the guest matrix when a guest is not using the
>> +mdev matrix device, an error will be displayed (ENODEV). Note that adapters and
>> +domains that are not yet available or not yet assigned to the LPAR can be
>> +assigned and will become available to the guest as soon as they become available
>> +to the host.
>> +
>> +Dynamic Changes to AP Configuration using the Support Element (SE):
>> +==================================================================
>> +The SE can be used to dynamically make the following changes to the AP
>> +configuration for an LPAR in which a linux host is running:
>> +
>> + * Configure one or more adapters on
>> +
>> + Configuring an adapter on sets its state to online, thus making it
>> + available to the LPAR to which it is assigned. When an adapter is
>> + configured on, it immediately becomes available to the LPAR as well as to
>> + any guests using a mediated device to which the adapter is assigned.
>> +
>> + * Configure one or more adapters off
>> +
>> + Configuring an adapter off sets its state to standby, thus making it
>> + unavailable to the LPAR to which it is assigned. When an adapter is
>> + configured off, it immediately becomes unavailable to the LPAR as well as
>> + to any guests using a mediated device to which the adapter is assigned.
>> +
>> + * Add adapters or domains to the LPAR configuration
>> +
>> + Adapters and/or domains can be assigned to an LPAR using the Change LPAR
>> + Cryptographic Controls task. To make dynamic changes to the AP
>> + configuration for an LPAR Running a linux guest, the online adapters
>> + assigned to the LPAR must first be configured off. After performing the
>> + adapter and/or domain assignments, the AP resources will automatically
>> + become available to the linux host running in the LPAR as well as any
>> + guests using a mediated device to which the adpaters and/or domains are
>> + assigned.
>> +
>> + * Remove adapters or domains from the LPAR configuration
>> +
>> + Adapters and/or domains can be unassigned from an LPAR using the Change
>> + LPAR Cryptographic Controls task. To make dynamic changes to the AP
>> + configuration for an LPAR Running a linux guest, the online adapters
>> + assigned to the LPAR must first be configured off. After performing the
>> + adapter and/or domain unassignments, the AP resources will automatically
>> + become unavailable to the linux host running in the LPAR as well as any
>> + guests using a mediated device to which the adpaters and/or domains are
>> + assigned.
>> +
>> +Dynamic Changes to the AP Configuration using the SCLP command:
>> +==============================================================
>> +The following SCLP commands may be used to dynamically configure AP adapters on
>> +and off:
>> +
>> +* Configure Adjunct Processor
>> +
>> + The 'Configure Adjunct Processor' command sets an AP adapter's state to
>> + online, thus making it available to the LPARs to which it is assigned. It will
>> + likewise become available to any linux guest using a mediated device to which
>> + the adapter is assigned.
>> +
>> +* Deconfigure Adjunct Processor
>> +
>> + The 'Deconfigure Adjunct Processor' command sets an AP adapter's state to
>> + standby, thus making it unavailable to the LPARs to which it is assigned. It
>> + will likewise become unavailable to any linux guest using a mediated device to
>> + which the adapter is assigned.
>>
>> -* Dynamically modifying the AP matrix for a running guest (which would amount to
>> - hot(un)plug of AP devices for the guest) is currently not supported
>> +Live migration:
>> +==============
>> +Live guest migration is not supported for guests using AP devices. All AP
>> +devices in use by the guest must be unplugged prior to initiating live
>> +migration (see "Hot plug/unplug via mdev matrix device sysfs interfaces" section
>> +above). If you are using QEMU to run your guest and it supports hot plug/unplug
>> +of the vfio-ap device, this would be another option (consult the QEMU
>> +documentation for details).
>>
>> -* Live guest migration is not supported for guests using AP devices.
>

\
 
 \ /
  Last update: 2019-06-17 17:22    [W:0.123 / U:0.080 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site