lkml.org 
[lkml]   [2019]   [May]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 2/2] hwmon: scmi: Scale values to target desired HWMON units
From
Date
On 5/7/19 6:55 AM, Guenter Roeck wrote:
> Hi Florian,
>
> On 5/6/19 3:41 PM, Florian Fainelli wrote:
>> If the SCMI firmware implementation is reporting values in a scale that
>> is different from the HWMON units, we need to scale up or down the value
>> according to how far appart they are.
>>
>> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
>> ---
>>   drivers/hwmon/scmi-hwmon.c | 55 +++++++++++++++++++++++++++++++-------
>>   1 file changed, 46 insertions(+), 9 deletions(-)
>>
>> diff --git a/drivers/hwmon/scmi-hwmon.c b/drivers/hwmon/scmi-hwmon.c
>> index a80183a488c5..e9913509cb88 100644
>> --- a/drivers/hwmon/scmi-hwmon.c
>> +++ b/drivers/hwmon/scmi-hwmon.c
>> @@ -18,6 +18,51 @@ struct scmi_sensors {
>>       const struct scmi_sensor_info **info[hwmon_max];
>>   };
>>   +static enum hwmon_sensor_types scmi_types[] = {
>> +    [TEMPERATURE_C] = hwmon_temp,
>> +    [VOLTAGE] = hwmon_in,
>> +    [CURRENT] = hwmon_curr,
>> +    [POWER] = hwmon_power,
>> +    [ENERGY] = hwmon_energy,
>> +};
>> +
>> +static u64 scmi_hwmon_scale(const struct scmi_sensor_info *sensor,
>> u64 value)
>> +{
>> +    u64 scaled_value = value;
>
> I don't think that variable is necessary.
>
>> +    s8 desired_scale;
>
> Just scale ? Also, you could assign scale here directly, and subtract
> the offset below. Then "n" would not be necessary.
> Such as
>     s8 scale = sensor->scale;    // assuming scale is s8
>     ...
>     case CURRENT:
>         scale += 3;
>     ...
>
> That would also be less confusing, since it would avoid the double
> negation.
>
>> +    int n, p;
>
>> +
>> +    switch (sensor->type) {
>> +    case TEMPERATURE_C:
>> +    case VOLTAGE:
>> +    case CURRENT:
>> +        /* fall through */
> Unnecessary comment

Is not removing the comment going to upset gcc when using
-Wimplicit-fallthrough?

>
>> +        desired_scale = -3;
>> +        break;
>> +    case POWER:
>> +    case ENERGY:
>> +        /* fall through */
> Unnecessary comment.
>
>> +        desired_scale = -6;
>> +        break;
>> +    default:
>> +        return scaled_value;
>
> Here we presumably want a scale of 0. However, if the scale passed
> from SCMI is, say, -5 or +5, we return the original (unadjusted)
> value. Seems to me we would still want to adjust the value to match
> hwmon expectations. Am I missing something ?

You raise a valid point, not that could happen today because if the
sensor type has a value we don't recognize, we have not registered it,
so we would not even try to read rom it, but let's be future proof.

>
>> +    }
>> +
>> +    n = (s8)sensor->scale - desired_scale;
>> +        if (n == 0)
>
> Indentation seems off here.
>
>> +                return scaled_value;
>> +
>> +    for (p = 0; p < abs(n); p++) {
>> +        /* Need to scale up from sensor to HWMON */
>> +        if (n > 0)
>> +            scaled_value *= 10;
>> +        else
>> +            do_div(scaled_value, 10);
>> +    }
>
> Something like
>
>     factor = pow10(abs(scale));
>     if (scale > 0)
>         value *= factor;
>     else
>         do_div(value, factor);
>
> would avoid the repeated abs() and do_div(). Unfortunately there is
> no pow10() helper, so you would have to write that. Still, I think
> that would be much more efficient.

Sounds reasonable. Thanks for your feedback!
--
Florian

\
 
 \ /
  Last update: 2019-05-07 19:45    [W:0.053 / U:0.344 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site