lkml.org 
[lkml]   [2019]   [Mar]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 4/5] mmc: mmci: stm32: define get_dctrl_cfg
From
Date


On 3/6/19 2:31 PM, Ulf Hansson wrote:
> On Mon, 4 Mar 2019 at 11:17, Ludovic Barre <ludovic.Barre@st.com> wrote:
>>
>> From: Ludovic Barre <ludovic.barre@st.com>
>>
>> This patch defines get_dctrl_cfg callback for sdmmc variant.
>> sdmmc variant has specific stm32 transfer modes.
>> sdmmc data transfer mode selection could be:
>> -Block data transfer ending on block count.
>> -SDIO multibyte data transfer.
>> -MMC Stream data transfer (not used).
>> -Block data transfer ending with STOP_TRANSMISSION command.
>>
>> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
>> ---
>> drivers/mmc/host/mmci.h | 5 +++++
>> drivers/mmc/host/mmci_stm32_sdmmc.c | 21 +++++++++++++++++++++
>> 2 files changed, 26 insertions(+)
>>
>> diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
>> index 6f28f71..eb5d99af 100644
>> --- a/drivers/mmc/host/mmci.h
>> +++ b/drivers/mmc/host/mmci.h
>> @@ -131,6 +131,11 @@
>> /* Control register extensions in the Qualcomm versions */
>> #define MCI_DPSM_QCOM_DATA_PEND BIT(17)
>> #define MCI_DPSM_QCOM_RX_DATA_PEND BIT(20)
>> +/* Control register extensions in STM32 versions */
>> +#define MCI_DPSM_STM32_MODE_BLOCK (0 << 2)
>> +#define MCI_DPSM_STM32_MODE_SDIO (1 << 2)
>> +#define MCI_DPSM_STM32_MODE_STREAM (2 << 2)
>> +#define MCI_DPSM_STM32_MODE_BLOCK_STOP (3 << 2)
>>
>> #define MMCIDATACNT 0x030
>> #define MMCISTATUS 0x034
>> diff --git a/drivers/mmc/host/mmci_stm32_sdmmc.c b/drivers/mmc/host/mmci_stm32_sdmmc.c
>> index cfbfc6f..e7bf744 100644
>> --- a/drivers/mmc/host/mmci_stm32_sdmmc.c
>> +++ b/drivers/mmc/host/mmci_stm32_sdmmc.c
>> @@ -265,10 +265,31 @@ static void mmci_sdmmc_set_pwrreg(struct mmci_host *host, unsigned int pwr)
>> }
>> }
>>
>> +u32 sdmmc_get_dctrl_cfg(struct mmci_host *host)
>> +{
>> + struct variant_data *variant = host->variant;
>> + int blksz_bits;
>> + u32 datactrl;
>> +
>> + blksz_bits = ffs(host->data->blksz) - 1;
>> + datactrl = variant->datactrl_dpsm_enable | blksz_bits << 4;
>> +
>> + if (host->mmc->card && mmc_card_sdio(host->mmc->card) &&
>> + host->data->blocks == 1)
>
> These settings are not limited to deal with the block size bits.
>
> Don't get me wrong, it seems reasonable to include them, but the
> generic code in mmci_start_data() also have code to cope with SDIO. I
> think we should start by splitting that up into a couple of
> helper/library functions, and make the legacy variant to use them.
> This should probably be done as a preparation to your series, so you
> can build on top of that.

I think you wish helper functions for each group of datactrl feature,
like for dpsm direction|sdio|ios timming. Each variant call theses
helpers to define its own datactrl value. it's possible, no problem.

In mmci_start_data will remain the part on clk_reg for sdio card
if (host->mmc->card && mmc_card_sdio(host->mmc->card)) {
u32 clk;

/*
* The ST Micro variant for SDIO small write transfers
* needs to have clock H/W flow control disabled,
* otherwise the transfer will not start. The threshold
* depends on the rate of MCLK.
*/
if (variant->st_sdio && data->flags & MMC_DATA_WRITE &&
(host->size < 8 ||
(host->size <= 8 && host->mclk > 50000000)))
clk = host->clk_reg & ~variant->clkreg_enable;
else
clk = host->clk_reg | variant->clkreg_enable;

mmci_write_clkreg(host, clk);
}

it's OK ?

>
> Does it make sense? If not, please tell and I can try to provide some
> patch to show you what I mean.
>
>
>> + datactrl |= MCI_DPSM_STM32_MODE_SDIO;
>> + else if (host->data->stop && !host->mrq->sbc)
>> + datactrl |= MCI_DPSM_STM32_MODE_BLOCK_STOP;
>> + else
>> + datactrl |= MCI_DPSM_STM32_MODE_BLOCK;
>> +
>> + return datactrl;
>> +}
>> +
>> static struct mmci_host_ops sdmmc_variant_ops = {
>> .validate_data = sdmmc_idma_validate_data,
>> .prep_data = sdmmc_idma_prep_data,
>> .unprep_data = sdmmc_idma_unprep_data,
>> + .get_datactrl_cfg = sdmmc_get_dctrl_cfg,
>> .dma_setup = sdmmc_idma_setup,
>> .dma_start = sdmmc_idma_start,
>> .dma_finalize = sdmmc_idma_finalize,
>> --
>> 2.7.4
>>
>
> Kind regards
> Uffe
>

\
 
 \ /
  Last update: 2019-03-06 18:02    [W:0.043 / U:0.104 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site