lkml.org 
[lkml]   [2019]   [Mar]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 3/3] drm/panel: Add Rocktech jh057n00900 panel driver
Hi,
On Fri, Mar 01, 2019 at 11:39:06PM +0100, Sam Ravnborg wrote:
> Hi Guido.
>
> Thanks for addressing review comments in first round.
> Just a few nits in this follow-up.
> With these nits addressed:
> Reviewed-by: Sam Ravnborg <sam@ravnborg.org>

Thanks! I made all the suggested changes in v3, on top of that I
prepended 'panel-rockteck-' to the driver name to be more consistent
with other drivers.
-- Guido

>
> On Fri, Mar 01, 2019 at 02:02:04PM +0100, Guido Günther wrote:
>
> > +#include <video/display_timing.h>
> This include file is, as far as I could tell, no longer used and can be dropped.
>
> > +
> > +static int jh057n_get_modes(struct drm_panel *panel)
> > +{
> > + struct drm_display_mode *mode;
> > +
> > + mode = drm_mode_duplicate(panel->drm, &default_mode);
> > + if (!mode) {
> > + DRM_ERROR("Failed to add mode %ux%u@%u",
> > + default_mode.hdisplay, default_mode.vdisplay,
> > + default_mode.vrefresh);
> > + return -ENOMEM;
> Use DRM_DEV_ERROR()
> You can find dev via: panel->base.drm-dev
>
> > +
> > +static int jh057n_probe(struct mipi_dsi_device *dsi)
> > +{
> > + struct device *dev = &dsi->dev;
> > + struct jh057n *ctx;
> > + int ret;
> > +
> > + ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
> > + if (!ctx)
> > + return -ENOMEM;
> > +
> > + ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
> > + if (IS_ERR(ctx->reset_gpio)) {
> > + DRM_DEV_ERROR(dev, "cannot get reset gpio");
> > + return PTR_ERR(ctx->reset_gpio);
> > + }
> > +
> > + mipi_dsi_set_drvdata(dsi, ctx);
> > +
> > + ctx->dev = dev;
> > +
> > + dsi->lanes = 4;
> > + dsi->format = MIPI_DSI_FMT_RGB888;
> > + dsi->mode_flags = MIPI_DSI_MODE_VIDEO |
> > + MIPI_DSI_MODE_VIDEO_BURST | MIPI_DSI_MODE_VIDEO_SYNC_PULSE;
> > +
> > + ctx->backlight = devm_of_find_backlight(dev);
> > + if (IS_ERR(ctx->backlight))
> > + return PTR_ERR(ctx->backlight);
> > +
> > + drm_panel_init(&ctx->panel);
> > + ctx->panel.dev = dev;
> > + ctx->panel.funcs = &jh057n_drm_funcs;
> > +
> > + drm_panel_add(&ctx->panel);
> > +
> > + ret = mipi_dsi_attach(dsi);
> > + if (ret < 0) {
> > + DRM_DEV_ERROR(dev, "mipi_dsi_attach failed. Is host ready?");
> > + drm_panel_remove(&ctx->panel);
> > + return ret;
> > + }
> > +
> > + DRM_INFO(DRV_NAME "_panel %ux%u@%u %ubpp dsi %udl - ready",
> > + default_mode.hdisplay, default_mode.vdisplay,
> > + default_mode.vrefresh,
> > + mipi_dsi_pixel_format_to_bpp(dsi->format), dsi->lanes);
>
> You already have dev, so use DRM_DEV_INFO() and drop DRV_NAME
>
> > +
> > +static const struct of_device_id jh057n_of_match[] = {
> > + { .compatible = "rocktech,jh057n00900" },
> > + { /* Sentinel */ }
> Lower case 's' (sorry, likely my bad)
>
> > + .probe = jh057n_probe,
> > + .remove = jh057n_remove,
> > + .shutdown = jh057n_shutdown,
> > + .driver = {
> > + .name = DRV_NAME "_panel",
> Drop "_panel" postfix. Other drivers do not use it.
>
> Sam
>

\
 
 \ /
  Last update: 2019-03-04 18:55    [W:0.071 / U:0.072 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site