lkml.org 
[lkml]   [2019]   [Mar]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH net-next v2 3/3] net: phy: marvell10g: set the PHY in low power by default
Hi Florian,

On Fri, Mar 01, 2019 at 07:08:56PM -0800, Florian Fainelli wrote:
> On 3/1/2019 7:07 AM, Antoine Tenart wrote:
> > On Fri, Mar 01, 2019 at 03:19:53PM +0100, Andrew Lunn wrote:
> >> On Fri, Mar 01, 2019 at 12:00:47PM +0100, Antoine Tenart wrote:
> >>> When the Marvell 10G PHYs are set out of reset, the LPOWER bit is set
> >>> depending on an hardware configuration choice. We also do not know what
> >>> is the PHY state at boot time. Hence, set the PHY in low power by
> >>> default when this driver probes.
> >>
> >> Florian did some work for c22 PHYs so that the existing link state
> >> could be used at boot. So for example, the bootloader configured the
> >> PHY up and it got link, there is no need to down/up the PHY when linux
> >> takes control. The networking comes up faster that way.
> >>
> >> Can this work for this PHY?
> >
> > This use case (the bootloader configures the PHY, Linux boots and sets
> > an interface using this PHY up) would work, and is what's happening in
> > some situations right now (the 3310 reset is never asserted prior to
> > this series).
> >
> > But consider this case (let's say we use a 10G link):
> >
> > ---------------- ----------------
> > | Board 1 | | Board 2 |
> > | MAC — 3310 — | — SFP cable — | — 3310 — MAC |
> > ---------------- ----------------
> >
> > Board 1: The userspace do not set the interface up. The MAC is in reset
> > (default state during the MAC driver probe), the PHY was
> > configured by the bootloader.
> > Board 2: The userspace set the interface up. The MAC is configured, the
> > PHY is configured as well.
> >
> > The two PHY's PCS will establish a link and report it as being up. In
> > this case, phylink's AN mode is MLO_AN_PHY and thus will report the
> > overall link as being the PHY's link status: up.
> >
> > My understanding is that the issue arises because the PHYs were never
> > set in reset, or low power, and thus act as if the user wanted the port
> > to be up. As the default behaviour for networking ports is to be down at
> > boot, I thought to set the PHY as well in a default low power state.
>
> The policy you are creating here for the marvell10g driver is entirely
> applicable to any PHY <=> PHY configuration where either of the two
> software agents on Board 1 or Board 2 has not had a chance to bring-up
> its bootloader/OS/applications to control the PHY.

Right.

> A number of PHYs come up fully on (or in isolate or super isolate mode)
> and will AN with their link partner if connected. For some people it's a
> feature, for some it is a waste of power. I don't necessarily have an
> issue with your patch per-se, but it does create an one off behavior
> that other PHY drivers may not follow.

I agree having a per-driver behaviour is not something we want. As I
understand it, there is no behaviour enforced currently regarding this
matter. I agree both cases have their pros and cons:
- It's weird to have an interface reporting being UP when it's not
really.
- Having the link come up faster can be a feature.

I have some questions then:
- Do you think calling suspend() in the core when probing a PHY driver
would work for all PHYs?
- Would a new Kconfig option selecting the default behaviour at boot
time be a solution?
- Or this is a WONTFIX kind of (small) issues? :)

Thanks!
Antoine

--
Antoine Ténart, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

\
 
 \ /
  Last update: 2019-03-04 11:29    [W:0.078 / U:0.676 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site