lkml.org 
[lkml]   [2019]   [Mar]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Subject[PATCH 00/10] Add Tegra194 PCIe support
Date
Tegra194 has six PCIe controllers based on Synopsys DesignWare core.
There are two Universal PHY (UPHY) blocks with each supporting 12(HSIO:
Hisg Speed IO) and 8(NVHS: NVIDIA High Speed) lanes respectively.
Controllers:0~4 use UPHY lanes from HSIO brick whereas Controller:5 uses
UPHY lanes from NVHS brick. Lane mapping in HSIO UPHY brick to each PCIe
controller (0~4) is controlled in XBAR module by BPMP-FW. Since PCIe
core has PIPE interface, a glue module called PIPE-to-UPHY (P2U) is used
to connect each UPHY lane (applicable to both HSIO and NVHS UPHY bricks)
to PCIe controller
This patch series
- Adds support for P2U PHY driver
- Adds support for PCIe host controller
- Adds device tree nodes each PCIe controllers
- Enables nodes applicable to p2972-0000 platform
- Adds helper APIs in Designware core driver to get capability regs offset
- Adds defines for new feature registers of PCIe spec revision 4
- Makes changes in DesignWare core driver to get Tegra194 PCIe working

Testing done on P2972-0000 platform
- Able to get PCIe link up with on-board Marvel eSATA controller
- Able to get PCIe link up with NVMe cards connected to M.2 Key-M slot
- Able to do data transfers with both SATA drives and NVMe cards

Note
- Enabling x8 slot on P2972-0000 platform requires pinmux driver for Tegra194.
It is being worked on currently and hence Controller:5 (i.e. x8 slot) is
disabled in this patch series. A future patch series would enable this.
Vidya Sagar (10):
PCI: save pci_bus pointer in pcie_port structure
PCI: perform dbi regs write lock towards the end
PCI: dwc: Move config space capability search API
PCI: Add #defines for PCIe spec r4.0 features
dt-bindings: PCI: tegra: Add device tree support for T194
arm64: tegra: Add P2U and PCIe controller nodes to Tegra194 DT
arm64: tegra: Enable PCIe slots in P2972-0000 board
phy: tegra: Add PCIe PIPE2UPHY support
PCI: tegra: Add Tegra194 PCIe support
arm64: Add Tegra194 PCIe driver to defconfig

.../bindings/pci/nvidia,tegra194-pcie.txt | 209 +++
.../devicetree/bindings/phy/phy-tegra194-p2u.txt | 34 +
arch/arm64/boot/dts/nvidia/tegra194-p2888.dtsi | 2 +-
arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts | 50 +
arch/arm64/boot/dts/nvidia/tegra194.dtsi | 473 +++++
arch/arm64/configs/defconfig | 1 +
drivers/pci/controller/dwc/Kconfig | 10 +
drivers/pci/controller/dwc/Makefile | 1 +
drivers/pci/controller/dwc/pcie-designware-ep.c | 37 +-
drivers/pci/controller/dwc/pcie-designware-host.c | 4 +-
drivers/pci/controller/dwc/pcie-designware.c | 73 +
drivers/pci/controller/dwc/pcie-designware.h | 4 +
drivers/pci/controller/dwc/pcie-tegra194.c | 1862 ++++++++++++++++++++
drivers/phy/tegra/Kconfig | 7 +
drivers/phy/tegra/Makefile | 1 +
drivers/phy/tegra/pcie-p2u-tegra194.c | 138 ++
include/uapi/linux/pci_regs.h | 22 +-
17 files changed, 2888 insertions(+), 40 deletions(-)
create mode 100644 Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt
create mode 100644 Documentation/devicetree/bindings/phy/phy-tegra194-p2u.txt
create mode 100644 drivers/pci/controller/dwc/pcie-tegra194.c
create mode 100644 drivers/phy/tegra/pcie-p2u-tegra194.c

--
2.7.4

\
 
 \ /
  Last update: 2019-03-26 16:15    [W:1.263 / U:0.156 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site