lkml.org 
[lkml]   [2019]   [Mar]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 5/5] lib/vsprintf: Add %pfw conversion specifier for printing fwnode names
Hi Andy,

On Tue, Mar 26, 2019 at 03:13:53PM +0200, Andy Shevchenko wrote:
> On Sun, Mar 24, 2019 at 08:17:46PM +0200, Sakari Ailus wrote:
> > On Fri, Mar 22, 2019 at 07:21:14PM +0200, Andy Shevchenko wrote:
> > > On Fri, Mar 22, 2019 at 05:29:30PM +0200, Sakari Ailus wrote:
> > > > Add support for %pfw conversion specifier (with "f" and "P" modifiers) to
> > > > support printing full path of the node, including its name ("f") and only
> > > > the node's name ("P") in the printk family of functions. The two flags
> > > > have equivalent functionality to existing %pOF with the same two modifiers
> > > > ("f" and "P") on OF based systems. The ability to do the same on ACPI
> > > > based systems is added by this patch.
> > >
> > > Do we encourage people to use it instead of %pOF cases where it is suitable?
> >
> > For code that is used on both OF and ACPI based systems, I think so. But if
> > you have something that is only used on OF, %pOF is better --- it has more
> > functionality that seems quite OF specific. In general I think the ability
> > to print a node's full name is way more important on OF. On ACPI you don't
> > need it so often --- which is probably the reason it hasn't been supported.
>
> But if code is going to support ACPI and DT and at the same time use %pOF
> extensions that are not covered by %pfw it would be inconsistent somehow.

What you mostly need are the full name and the name of a given node. I
wasn't sure whether adding more would have been relevant, and at least it
is likely to have few if any users, so I didn't add that yet. Do not that
it can be implemented later on if it's needed --- that's also why the
modifiers are aligned with %pOF.

>
> > > > On ACPI based systems the resulting strings look like
> > > >
> > > > \_SB.PCI0.CIO2.port@1.endpoint@0
> > > >
> > > > where the nodes are separated by a dot (".") and the first three are
> > > > ACPI device nodes and the latter two ACPI data nodes.
> > >
> > > Do we support swnode here?
> >
> > Good question. The swnodes have no hierarchy at the moment (they're only
> > created for a struct device as a parent) and they do not have human-readable
> > names. So I'd say it's not relevant right now. Should these two change,
> > support for swnode could (and should) be added later on.
>
> Heikki, what do you think about this?
>
> > > > + if ((unsigned long)fwnode < PAGE_SIZE)
> > > > + return string(buf, end, "(null)", spec);
> > >
> > > Just put there a NULL pointer, we would not like to maintain duplicated strings
> > > over the kernel.
> > >
> > > I remember Petr has a patch series related to address space check, though I
> > > don't remember the status of affairs.
> >
> > This bit has been actually adopted from the OF counterpart. If there are
> > improvements in this area, then I'd just change both at the same time.
>
> The patch series by Petr I mentioned takes care about OF case. But it doesn't
> have covered yours by obvious reasons.

Do you happen to have a pointer to it?

>
> > > > + for (pass = false; strspn(fmt, modifiers); fmt++, pass = true) {
> > >
> > > I don't see test cases.
> > >
> > > What would we get out of %pfwfffPPPfff?
> > >
> > > Hint: I'm expecting above to be equivalent to %pfwf
> >
> > I guess it's a matter of expectations. :-)
>
> Common sense and basic expectations from all of %p extensions.
>
> > Again this works the same way
> > than the OF counterpart.
>
> OF lacks of testing apparently.
>
> > Right now there's little to print (just the name
> > and the full name), but if support is added for more, then this mechanism is
> > fully relevant again.
> >
> > The alternative would be to remove that now and add it back if it's needed
> > again. I have a slight preference towards keeping it extensible (i.e. as
> > it's now).
>
> See how other helpers do parse this.

The behaviour on others is different indeed, you're generally printing a
single item at a time. The question rather is, whether we want to be
compatible with %pOF going forward or not. I'd prefer that, so using the
fwnode API would be easier.

--
Regards,

Sakari Ailus
sakari.ailus@linux.intel.com

\
 
 \ /
  Last update: 2019-03-26 14:41    [W:0.191 / U:0.172 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site