lkml.org 
[lkml]   [2019]   [Mar]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
Subject[PATCH 1/2] devantech-srf04.yaml: transform DT binding to YAML
use devantech-srf04.txt and transform binding into yaml

Signed-off-by: Andreas Klinger <ak@it-klinger.de>
---
.../bindings/iio/proximity/devantech-srf04.yaml | 62 ++++++++++++++++++++++
1 file changed, 62 insertions(+)
create mode 100644 Documentation/devicetree/bindings/iio/proximity/devantech-srf04.yaml

diff --git a/Documentation/devicetree/bindings/iio/proximity/devantech-srf04.yaml b/Documentation/devicetree/bindings/iio/proximity/devantech-srf04.yaml
new file mode 100644
index 000000000000..cd065393b062
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/proximity/devantech-srf04.yaml
@@ -0,0 +1,62 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/proximity/devantech-srf04.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Devantech SRF04 ultrasonic range finder
+
+maintainers:
+ - Andreas Klinger <ak@it-klinger.de>
+
+description: |
+ Bit-banging driver using two GPIOs:
+ - trigger-gpio is raised by the driver to start sending out an ultrasonic
+ burst
+ - echo-gpio is held high by the sensor after sending ultrasonic burst
+ until it is received once again
+
+ Specifications about the driver can be found at:
+ http://www.robot-electronics.co.uk/htm/srf04tech.htm
+
+allOf:
+ - $ref: /schemas/i2c/i2c-controller.yaml#
+
+properties:
+ compatible:
+ items:
+ - const: devantech,srf04
+
+ trig-gpios:
+ description:
+ Definition of the GPIO for the triggering (output) This GPIO is set
+ for about 10 us by the driver to tell the device it should initiate
+ the measurement cycle.
+ maxItems: 1
+
+ echo-gpios:
+ description:
+ Definition of the GPIO for the echo (input)
+ This GPIO is set by the device as soon as an ultrasonic burst is sent
+ out and reset when the first echo is received.
+ Thus this GPIO is set while the ultrasonic waves are doing one round
+ trip.
+ It needs to be an GPIO which is able to deliver an interrupt because
+ the time between two interrupts is measured in the driver.
+ See Documentation/devicetree/bindings/gpio/gpio.txt for information
+ on how to specify a consumer gpio.
+ maxItems: 1
+
+required:
+ - compatible
+ - trig-gpios
+ - echo-gpios
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ proximity {
+ compatible = "devantech,srf04";
+ trig-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
+ echo-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>;
+ };
--
2.11.0
\
 
 \ /
  Last update: 2019-03-26 13:32    [W:0.585 / U:0.052 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site