lkml.org 
[lkml]   [2019]   [Mar]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2] arm64: dts: fsl: imx8mq: enable the multi sensor TMU
From
Date
Hi Angus,

Am Montag, den 18.03.2019, 11:46 -0700 schrieb Angus Ainslie (Purism):
> Add the imx8mq TMU (Thermal mannagement unit) nodes for CPU,
> GPU, and VPU.
>
> Changes since v1:
>
> Removed references to multi sensor patch.
>
> Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
> ---
>  arch/arm64/boot/dts/freescale/imx8mq.dtsi | 118 ++++++++++++++++++++++
>  1 file changed, 118 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
> index 9155bd4784eb..885395e74452 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi

[...]

> + thermal-zones {
> + cpu-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <2000>;
> + thermal-sensors = <&tmu 0>;
> +
> + trips {
> + cpu_alert: cpu-alert {
> + temperature = <85000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpu_crit {
> + temperature = <95000>;

All the critical trip points seem to be too high. The consumer parts
have a maximum junction temperature of 95°C, so the common DT
configuration used by all boards should have a crit trip point at least
a few degrees below this value. Boards that only use the industrial
parts can always overwrite the trip points if the designer wishes to do
so.

> + hysteresis = <2000>;
> + type = "critical";
> + };
> + };
> +
> + cooling-maps {
> + map0 {
> + trip = <&cpu_alert>;
> + cooling-device =
> + <&A53_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&A53_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&A53_2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> + <&A53_3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> + };
> + };
> + };
> +
> + gpu-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <2000>;
> + thermal-sensors = <&tmu 1>;
> +
> + trips {
> + cpu-crit {

Should be gpu-crit.

> + temperature = <95000>;
> + hysteresis = <2000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + vpu-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <2000>;
> + thermal-sensors = <&tmu 2>;
> +
> + trips {
> + cpu-crit {

Should be vpu-crit.

Regards,
Lucas

\
 
 \ /
  Last update: 2019-03-19 12:47    [W:0.147 / U:0.136 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site