lkml.org 
[lkml]   [2019]   [Mar]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 2/2] tty/serial: atmel: RS485 HD w/DMA: enable RX after TX is stopped
From
Date
[ adding Gil Weber in Cc: ]
Le 15/03/2019 à 10:23, Razvan Stefanescu a écrit :
> In half-duplex operation, RX should be started after TX completes.
>
> If DMA is used, there is a case when the DMA transfer completes but the
> TX FIFO is not emptied, so the RX cannot be restarted just yet.
>
> Use a boolean variable to store this state and rearm TX interrupt mask
> to be signaled again that the transfer finished. In interrupt transmit
> handler this variable is used to start RX.

I was sure I've already seen something like that.
Gil, could you give it a test ?

you can add :
Cc: stable@vger.kernel.org
Fixes: b389f173aaa1 ("tty/serial: atmel: RS485 half duplex w/DMA: enable RX after TX is done")

Since patch 1/2 is needed for this one, I think you should add also
Cc:stable / Fixes: to the previous patch.

> Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com>
> ---
> drivers/tty/serial/atmel_serial.c | 25 ++++++++++++++++++++++---
> 1 file changed, 22 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
> index a6577b1c4461..b0141dcbbb61 100644
> --- a/drivers/tty/serial/atmel_serial.c
> +++ b/drivers/tty/serial/atmel_serial.c
> @@ -166,6 +166,8 @@ struct atmel_uart_port {
> unsigned int pending_status;
> spinlock_t lock_suspended;
>
> + bool hd_start_rx; /* can start RX during half-duplex operation */
> +
> /* ISO7816 */
> unsigned int fidi_min;
> unsigned int fidi_max;
> @@ -934,8 +936,13 @@ static void atmel_complete_tx_dma(void *arg)
> if (!uart_circ_empty(xmit))
> atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_tx);
> else if (atmel_uart_is_half_duplex(port)) {
> - /* DMA done, stop TX, start RX for RS485 */
> - atmel_start_rx(port);
> + /*
> + * DMA done, re-enable TXEMPTY and signal that we can stop
> + * TX and start RX for RS485
> + */
> + atmel_port->hd_start_rx = true;
> + atmel_uart_writel(port, ATMEL_US_IER,
> + atmel_port->tx_done_mask);
> }
>
> spin_unlock_irqrestore(&port->lock, flags);
> @@ -1379,9 +1386,21 @@ atmel_handle_transmit(struct uart_port *port, unsigned int pending)
> struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
>
> if (pending & atmel_port->tx_done_mask) {
> - /* Either PDC or interrupt transmission */
> atmel_uart_writel(port, ATMEL_US_IDR,
> atmel_port->tx_done_mask);
> +
> + /* Start RX if flag was set and FIFO is empty */
> + if (atmel_port->hd_start_rx) {
> + if (atmel_uart_readl(port, ATMEL_US_CSR)
> + & ATMEL_US_TXEMPTY) {
> + atmel_port->hd_start_rx = false;
> + atmel_start_rx(port);
> + } else {
> + dev_warn(port->dev, "Should start RX, but TX fifo is not empty\n");
What will happen in this case ?

> + }
> + return;
> + }
> +
> atmel_tasklet_schedule(atmel_port, &atmel_port->tasklet_tx);
> }
> }
>

Thanks !

\
 
 \ /
  Last update: 2019-03-18 15:31    [W:0.059 / U:0.104 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site