lkml.org 
[lkml]   [2019]   [Mar]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 7/8] arm64: dts: meson: g12a: Add G12A USB nodes
Date
This patch adds the nodes for the USB Complex found in the Amlogic
G12A SoC.

It includes the :
- 2 USB2 PHYs
- 1 USB3 + PCIE Combo PHY
- the USB Glue with it's DWC2 and DWC3 sub-nodes

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
arch/arm64/boot/dts/amlogic/meson-g12a.dtsi | 75 +++++++++++++++++++++
1 file changed, 75 insertions(+)

diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
index a99c13ee724a..ce681aef8d5b 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
@@ -3,11 +3,13 @@
* Copyright (c) 2018 Amlogic, Inc. All rights reserved.
*/

+#include <dt-bindings/phy/phy.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/clock/g12a-clkc.h>
#include <dt-bindings/clock/g12a-aoclkc.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/reset/amlogic,meson-g12a-reset.h>

/ {
compatible = "amlogic,g12a";
@@ -163,6 +165,26 @@
};
};

+ usb2_phy0: phy@36000 {
+ compatible = "amlogic,g12a-usb2-phy";
+ reg = <0x0 0x36000 0x0 0x2000>;
+ clocks = <&xtal>;
+ clock-names = "xtal";
+ resets = <&reset RESET_USB_PHY20>;
+ reset-names = "phy";
+ #phy-cells = <0>;
+ };
+
+ usb2_phy1: phy@3a000 {
+ compatible = "amlogic,g12a-usb2-phy";
+ reg = <0x0 0x3a000 0x0 0x2000>;
+ clocks = <&xtal>;
+ clock-names = "xtal";
+ resets = <&reset RESET_USB_PHY21>;
+ reset-names = "phy";
+ #phy-cells = <0>;
+ };
+
hiu: bus@3c000 {
compatible = "simple-bus";
reg = <0x0 0x3c000 0x0 0x1400>;
@@ -183,6 +205,18 @@
};
};
};
+
+ usb3_pcie_phy: phy@46000 {
+ compatible = "amlogic,g12a-usb3-pcie-phy";
+ reg = <0x0 0x46000 0x0 0x2000>;
+ clocks = <&clkc CLKID_PCIE_PLL>;
+ clock-names = "ref_clk";
+ resets = <&reset RESET_PCIE_PHY>;
+ reset-names = "phy";
+ assigned-clocks = <&clkc CLKID_PCIE_PLL>;
+ assigned-clock-rates = <100000000>;
+ #phy-cells = <1>;
+ };
};

aobus: bus@ff800000 {
@@ -346,6 +380,47 @@
status = "disabled";
};
};
+
+ usb: usb@ffe09000 {
+ status = "disabled";
+ compatible = "amlogic,meson-g12a-usb-ctrl";
+ reg = <0x0 0xffe09000 0x0 0xa0>;
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ clocks = <&clkc CLKID_USB>;
+ resets = <&reset RESET_USB>;
+
+ dr_mode = "otg";
+
+ phys = <&usb2_phy0>, <&usb2_phy1>,
+ <&usb3_pcie_phy PHY_TYPE_USB3>;
+ phy-names = "usb2-phy0", "usb2-phy1", "usb3-phy0";
+
+ dwc2: usb@ff400000 {
+ compatible = "amlogic,meson-g12a-usb", "snps,dwc2";
+ reg = <0x0 0xff400000 0x0 0x40000>;
+ interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clkc CLKID_USB1_DDR_BRIDGE>;
+ clock-names = "ddr";
+ phys = <&usb2_phy1>;
+ dr_mode = "peripheral";
+ g-rx-fifo-size = <192>;
+ g-np-tx-fifo-size = <128>;
+ g-tx-fifo-size = <128 128 16 16 16>;
+ };
+
+ dwc3: usb@ff500000 {
+ compatible = "snps,dwc3";
+ reg = <0x0 0xff500000 0x0 0x100000>;
+ interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+ dr_mode = "host";
+ snps,dis_u2_susphy_quirk;
+ snps,quirk-frame-length-adjustment;
+ };
+ };
};

timer {
--
2.20.1
\
 
 \ /
  Last update: 2019-03-18 10:59    [W:0.107 / U:0.040 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site