lkml.org 
[lkml]   [2019]   [Mar]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] staging: comedi: ni_mio_common: Fix divide-by-zero for DIO cmdtest
On Wed, Mar 13, 2019 at 06:57:17PM +0000, Ian Abbott wrote:
> On 04/03/2019 14:33, Ian Abbott wrote:
> > `ni_cdio_cmdtest()` validates Comedi asynchronous commands for the DIO
> > subdevice (subdevice 2) of supported National Instruments M-series
> > cards. It is called when handling the `COMEDI_CMD` and `COMEDI_CMDTEST`
> > ioctls for this subdevice. There are two causes for a possible
> > divide-by-zero error when validating that the `stop_arg` member of the
> > passed-in command is not too large.
> >
> > The first cause for the divide-by-zero is that calls to
> > `comedi_bytes_per_scan()` are only valid once the command has been
> > copied to `s->async->cmd`, but that copy is only done for the
> > `COMEDI_CMD` ioctl. For the `COMEDI_CMDTEST` ioctl, it will use
> > whatever was left there by the previous `COMEDI_CMD` ioctl, if any.
> > (This is very likely, as it is usual for the application to use
> > `COMEDI_CMDTEST` before `COMEDI_CMD`.) If there has been no previous,
> > valid `COMEDI_CMD` for this subdevice, then `comedi_bytes_per_scan()`
> > will return 0, so the subsequent division in `ni_cdio_cmdtest()` of
> > `s->async->prealloc_bufsz / comedi_bytes_per_scan(s)` will be a
> > divide-by-zero error. To fix this error, call a new function
> > `comedi_bytes_per_scan_cmd(s, cmd)`, based on the existing
> > `comedi_bytes_per_scan(s)` but using a specified `struct comedi_cmd` for
> > its calculations. (Also refactor `comedi_bytes_per_scan()` to call the
> > new function.)
> >
> > Once the first cause for the divide-by-zero has been fixed, the second
> > cause is that `comedi_bytes_per_scan_cmd()` can legitimately return 0 if
> > the `scan_end_arg` member of the `struct comedi_cmd` being tested is 0.
> > Fix it by only performing the division (and validating that `stop_arg`
> > is no more than the maximum value) if `comedi_bytes_per_scan_cmd()`
> > returns a non-zero value.
> >
> > The problem was reported on the COMEDI mailing list here:
> > https://groups.google.com/forum/#!topic/comedi_list/4t9WlHzMhKM
> >
> > Fixes: f164cbf98fa8 ("staging: comedi: ni_mio_common: add finite regeneration to dio output")
>
> Greg,
> If it's not too late, it would be nice if the following "Reported-by:" and
> "Tested-by:" lines could be added (or I can resend with these lines included
> if necessary). It's no big deal if this is too late. I'll live with it.
> Thanks.
>
> Reported-by: Ivan Vasilyev <grabesstimme@gmail.com>
> Tested-by: Ivan Vasilyev <grabesstimme@gmail.com>

Not too late, I'll go add it now, thanks.

greg k-h

\
 
 \ /
  Last update: 2019-03-18 07:55    [W:0.087 / U:0.976 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site