lkml.org 
[lkml]   [2019]   [Mar]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v3 8/8] usb: dwc3: Add Amlogic G12A DWC3 glue
From
Date
Hi Neil,
On Mon, 2019-03-18 at 11:11 +0100, Neil Armstrong wrote:
> Adds support for Amlogic G12A USB Control Glue HW.
>
> The Amlogic G12A SoC Family embeds 2 USB Controllers :
> - a DWC3 IP configured as Host for USB2 and USB3
> - a DWC2 IP configured as Peripheral USB2 Only
>
> A glue connects these both controllers to 2 USB2 PHYs, and optionnally
> to an USB3+PCIE Combo PHY shared with the PCIE controller.
>
> The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including
> routing of the OTG PHY between the DWC3 and DWC2 controllers, and
> setups the on-chip OTG mode selection for this PHY.
>
> This drivers supports the on-probe setup of the OTG mode, and manually
> via a debugfs interface. The IRQ mode change detect is yet to be added
> in a future patchset, mainly due to lack of hardware to validate on.
>
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
> ---
> drivers/usb/dwc3/Kconfig | 10 +
> drivers/usb/dwc3/Makefile | 1 +
> drivers/usb/dwc3/dwc3-meson-g12a.c | 602 +++++++++++++++++++++++++++++
> 3 files changed, 613 insertions(+)
> create mode 100644 drivers/usb/dwc3/dwc3-meson-g12a.c
>
> diff --git a/drivers/usb/dwc3/Kconfig b/drivers/usb/dwc3/Kconfig
> index 2b1494460d0c..d2ea9670563c 100644
> --- a/drivers/usb/dwc3/Kconfig
> +++ b/drivers/usb/dwc3/Kconfig
> @@ -95,6 +95,16 @@ config USB_DWC3_KEYSTONE
> Support of USB2/3 functionality in TI Keystone2 and AM654 platforms.
> Say 'Y' or 'M' here if you have one such device
>
> +config USB_DWC3_MESON_G12A
> + tristate "Amlogic Meson G12A Platforms"
> + depends on OF && COMMON_CLK
> + depends on ARCH_MESON || COMPILE_TEST
> + default USB_DWC3
> + select USB_ROLE_SWITCH
> + help
> + Support USB2/3 functionality in Amlogic G12A platforms.
> + Say 'Y' or 'M' if you have one such device.
> +
> config USB_DWC3_OF_SIMPLE
> tristate "Generic OF Simple Glue Layer"
> depends on OF && COMMON_CLK
> diff --git a/drivers/usb/dwc3/Makefile b/drivers/usb/dwc3/Makefile
> index 6e3ef6144e5d..ae86da0dc5bd 100644
> --- a/drivers/usb/dwc3/Makefile
> +++ b/drivers/usb/dwc3/Makefile
> @@ -47,6 +47,7 @@ obj-$(CONFIG_USB_DWC3_EXYNOS) += dwc3-exynos.o
> obj-$(CONFIG_USB_DWC3_PCI) += dwc3-pci.o
> obj-$(CONFIG_USB_DWC3_HAPS) += dwc3-haps.o
> obj-$(CONFIG_USB_DWC3_KEYSTONE) += dwc3-keystone.o
> +obj-$(CONFIG_USB_DWC3_MESON_G12A) += dwc3-meson-g12a.o
> obj-$(CONFIG_USB_DWC3_OF_SIMPLE) += dwc3-of-simple.o
> obj-$(CONFIG_USB_DWC3_ST) += dwc3-st.o
> obj-$(CONFIG_USB_DWC3_QCOM) += dwc3-qcom.o
> diff --git a/drivers/usb/dwc3/dwc3-meson-g12a.c b/drivers/usb/dwc3/dwc3-meson-g12a.c
> new file mode 100644
> index 000000000000..9f4554e8e6e7
> --- /dev/null
> +++ b/drivers/usb/dwc3/dwc3-meson-g12a.c
> @@ -0,0 +1,602 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * USB Glue for Amlogic G12A SoCs
> + *
> + * Copyright (c) 2019 BayLibre, SAS
> + * Author: Neil Armstrong <narmstrong@baylibre.com>
> + */
> +
> +/*
> + * The USB is organized with a glue around the DWC3 Controller IP as :
> + * - Control registers for each USB2 Ports
> + * - Control registers for the USB PHY layer
> + * - SuperSpeed PHY can be enabled only if port is used
> + *
> + * TOFIX:
> + * - Add dynamic OTG switching with ID change interrupt
> + */
> +
> +#include <linux/module.h>
> +#include <linux/kernel.h>
> +#include <linux/platform_device.h>
> +#include <linux/clk.h>
> +#include <linux/of.h>
> +#include <linux/of_platform.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/regmap.h>
> +#include <linux/bitfield.h>
> +#include <linux/bitops.h>
> +#include <linux/reset.h>
> +#include <linux/phy/phy.h>
> +#include <linux/usb/otg.h>
> +#include <linux/usb/role.h>
> +#include <linux/regulator/consumer.h>
> +
> +/* USB2 Ports Control Registers */
> +
> +#define U2P_REG_SIZE 0x20
> +
> +#define U2P_R0 0x0
> + #define U2P_R0_HOST_DEVICE BIT(0)
> + #define U2P_R0_POWER_OK BIT(1)
> + #define U2P_R0_HAST_MODE BIT(2)
> + #define U2P_R0_POWER_ON_RESET BIT(3)
> + #define U2P_R0_ID_PULLUP BIT(4)
> + #define U2P_R0_DRV_VBUS BIT(5)
> +
> +#define U2P_R1 0x4
> + #define U2P_R1_PHY_READY BIT(0)
> + #define U2P_R1_ID_DIG BIT(1)
> + #define U2P_R1_OTG_SESSION_VALID BIT(2)
> + #define U2P_R1_VBUS_VALID BIT(3)
> +
> +/* USB Glue Control Registers */
> +
> +#define USB_R0 0x80
> + #define USB_R0_P30_LANE0_TX2RX_LOOPBACK BIT(17)
> + #define USB_R0_P30_LANE0_EXT_PCLK_REQ BIT(18)
> + #define USB_R0_P30_PCS_RX_LOS_MASK_VAL_MASK GENMASK(28, 19)
> + #define USB_R0_U2D_SS_SCALEDOWN_MODE_MASK GENMASK(30, 29)
> + #define USB_R0_U2D_ACT BIT(31)
> +
> +#define USB_R1 0x84
> + #define USB_R1_U3H_BIGENDIAN_GS BIT(0)
> + #define USB_R1_U3H_PME_ENABLE BIT(1)
> + #define USB_R1_U3H_HUB_PORT_OVERCURRENT_MASK GENMASK(4, 2)
> + #define USB_R1_U3H_HUB_PORT_PERM_ATTACH_MASK GENMASK(9, 7)
> + #define USB_R1_U3H_HOST_U2_PORT_DISABLE_MASK GENMASK(13, 12)
> + #define USB_R1_U3H_HOST_U3_PORT_DISABLE BIT(16)
> + #define USB_R1_U3H_HOST_PORT_POWER_CONTROL_PRESENT BIT(17)
> + #define USB_R1_U3H_HOST_MSI_ENABLE BIT(18)
> + #define USB_R1_U3H_FLADJ_30MHZ_REG_MASK GENMASK(24, 19)
> + #define USB_R1_P30_PCS_TX_SWING_FULL_MASK GENMASK(31, 25)
> +
> +#define USB_R2 0x88
> + #define USB_R2_P30_PCS_TX_DEEMPH_3P5DB_MASK GENMASK(25, 20)
> + #define USB_R2_P30_PCS_TX_DEEMPH_6DB_MASK GENMASK(31, 26)
> +
> +#define USB_R3 0x8c
> + #define USB_R3_P30_SSC_ENABLE BIT(0)
> + #define USB_R3_P30_SSC_RANGE_MASK GENMASK(3, 1)
> + #define USB_R3_P30_SSC_REF_CLK_SEL_MASK GENMASK(12, 4)
> + #define USB_R3_P30_REF_SSP_EN BIT(13)
> +
> +#define USB_R4 0x90
> + #define USB_R4_P21_PORT_RESET_0 BIT(0)
> + #define USB_R4_P21_SLEEP_M0 BIT(1)
> + #define USB_R4_MEM_PD_MASK GENMASK(3, 2)
> + #define USB_R4_P21_ONLY BIT(4)
> +
> +#define USB_R5 0x94
> + #define USB_R5_ID_DIG_SYNC BIT(0)
> + #define USB_R5_ID_DIG_REG BIT(1)
> + #define USB_R5_ID_DIG_CFG_MASK GENMASK(3, 2)
> + #define USB_R5_ID_DIG_EN_0 BIT(4)
> + #define USB_R5_ID_DIG_EN_1 BIT(5)
> + #define USB_R5_ID_DIG_CURR BIT(6)
> + #define USB_R5_ID_DIG_IRQ BIT(7)
> + #define USB_R5_ID_DIG_TH_MASK GENMASK(15, 8)
> + #define USB_R5_ID_DIG_CNT_MASK GENMASK(23, 16)
> +
> +enum {
> + USB2_HOST_PHY = 0,
> + USB2_OTG_PHY,
> + USB3_HOST_PHY,
> + PHY_COUNT,
> +};
> +
> +static const char *phy_names[PHY_COUNT] = {
> + "usb2-phy0", "usb2-phy1", "usb3-phy0",
> +};
> +
> +struct dwc3_meson_g12a {
> + struct device *dev;
> + struct regmap *regmap;
> + struct clk *clk;
> + struct reset_control *reset;
> + struct phy *phys[PHY_COUNT];
> + enum usb_dr_mode otg_mode;
> + enum phy_mode otg_phy_mode;
> + unsigned int usb2_ports;
> + unsigned int usb3_ports;
> + struct regulator *vbus;
> + struct usb_role_switch_desc switch_desc;
> + struct usb_role_switch *role_switch;
> +};
> +
> +static void dwc3_meson_g12a_usb2_set_mode(struct dwc3_meson_g12a *priv,
> + int i, enum phy_mode mode)
> +{
> + if (mode == PHY_MODE_USB_HOST)
> + regmap_update_bits(priv->regmap, U2P_R0 + (U2P_REG_SIZE * i),
> + U2P_R0_HOST_DEVICE,
> + U2P_R0_HOST_DEVICE);
> + else
> + regmap_update_bits(priv->regmap, U2P_R0 + (U2P_REG_SIZE * i),
> + U2P_R0_HOST_DEVICE, 0);
> +}
> +
> +static int dwc3_meson_g12a_usb2_init(struct dwc3_meson_g12a *priv)
> +{
> + int i;
> +
> + if (priv->otg_mode == USB_DR_MODE_PERIPHERAL)
> + priv->otg_phy_mode = PHY_MODE_USB_DEVICE;
> + else
> + priv->otg_phy_mode = PHY_MODE_USB_HOST;
> +
> + for (i = 0 ; i < USB3_HOST_PHY ; ++i) {
> + if (!priv->phys[i])
> + continue;
> +
> + regmap_update_bits(priv->regmap, U2P_R0 + (U2P_REG_SIZE * i),
> + U2P_R0_POWER_ON_RESET,
> + U2P_R0_POWER_ON_RESET);
> +
> + if (i == USB2_OTG_PHY) {
> + regmap_update_bits(priv->regmap,
> + U2P_R0 + (U2P_REG_SIZE * i),
> + U2P_R0_ID_PULLUP | U2P_R0_DRV_VBUS,
> + U2P_R0_ID_PULLUP | U2P_R0_DRV_VBUS);
> +
> + dwc3_meson_g12a_usb2_set_mode(priv, i,
> + priv->otg_phy_mode);
> + } else
> + dwc3_meson_g12a_usb2_set_mode(priv, i,
> + PHY_MODE_USB_HOST);
> +
> + regmap_update_bits(priv->regmap, U2P_R0 + (U2P_REG_SIZE * i),
> + U2P_R0_POWER_ON_RESET, 0);
> + }
> +
> + return 0;
> +}
> +
> +static void dwc3_meson_g12a_usb3_init(struct dwc3_meson_g12a *priv)
> +{
> + regmap_update_bits(priv->regmap, USB_R3,
> + USB_R3_P30_SSC_RANGE_MASK |
> + USB_R3_P30_REF_SSP_EN,
> + USB_R3_P30_SSC_ENABLE |
> + FIELD_PREP(USB_R3_P30_SSC_RANGE_MASK, 2) |
> + USB_R3_P30_REF_SSP_EN);
> + udelay(2);
> +
> + regmap_update_bits(priv->regmap, USB_R2,
> + USB_R2_P30_PCS_TX_DEEMPH_3P5DB_MASK,
> + FIELD_PREP(USB_R2_P30_PCS_TX_DEEMPH_3P5DB_MASK, 0x15));
> +
> + regmap_update_bits(priv->regmap, USB_R2,
> + USB_R2_P30_PCS_TX_DEEMPH_6DB_MASK,
> + FIELD_PREP(USB_R2_P30_PCS_TX_DEEMPH_6DB_MASK, 0x20));
> +
> + udelay(2);
> +
> + regmap_update_bits(priv->regmap, USB_R1,
> + USB_R1_U3H_HOST_PORT_POWER_CONTROL_PRESENT,
> + USB_R1_U3H_HOST_PORT_POWER_CONTROL_PRESENT);
> +
> + regmap_update_bits(priv->regmap, USB_R1,
> + USB_R1_P30_PCS_TX_SWING_FULL_MASK,
> + FIELD_PREP(USB_R1_P30_PCS_TX_SWING_FULL_MASK, 127));
> +}
> +
> +static void dwc3_meson_g12a_usb_otg_apply_mode(struct dwc3_meson_g12a *priv)
> +{
> + if (priv->otg_phy_mode == PHY_MODE_USB_DEVICE) {
> + regmap_update_bits(priv->regmap, USB_R0,
> + USB_R0_U2D_ACT, USB_R0_U2D_ACT);
> + regmap_update_bits(priv->regmap, USB_R0,
> + USB_R0_U2D_SS_SCALEDOWN_MODE_MASK, 0);
> + regmap_update_bits(priv->regmap, USB_R4,
> + USB_R4_P21_SLEEP_M0, USB_R4_P21_SLEEP_M0);
> + } else {
> + regmap_update_bits(priv->regmap, USB_R0,
> + USB_R0_U2D_ACT, 0);
> + regmap_update_bits(priv->regmap, USB_R4,
> + USB_R4_P21_SLEEP_M0, 0);
> + }
> +}
> +
> +static int dwc3_meson_g12a_usb_init(struct dwc3_meson_g12a *priv)
> +{
> + int ret;
> +
> + ret = dwc3_meson_g12a_usb2_init(priv);
> + if (ret)
> + return ret;
> +
> + regmap_update_bits(priv->regmap, USB_R1,
> + USB_R1_U3H_FLADJ_30MHZ_REG_MASK,
> + FIELD_PREP(USB_R1_U3H_FLADJ_30MHZ_REG_MASK, 0x20));
> +
> + regmap_update_bits(priv->regmap, USB_R5,
> + USB_R5_ID_DIG_EN_0,
> + USB_R5_ID_DIG_EN_0);
> + regmap_update_bits(priv->regmap, USB_R5,
> + USB_R5_ID_DIG_EN_1,
> + USB_R5_ID_DIG_EN_1);
> + regmap_update_bits(priv->regmap, USB_R5,
> + USB_R5_ID_DIG_TH_MASK,
> + FIELD_PREP(USB_R5_ID_DIG_TH_MASK, 0xff));
> +
> + /* If we have an actual SuperSpeed port, initialize it */
> + if (priv->usb3_ports)
> + dwc3_meson_g12a_usb3_init(priv);
> +
> + dwc3_meson_g12a_usb_otg_apply_mode(priv);
> +
> + return 0;
> +}
> +
> +static const struct regmap_config phy_meson_g12a_usb3_regmap_conf = {
> + .reg_bits = 8,
> + .val_bits = 32,
> + .reg_stride = 4,
> + .max_register = USB_R5,
> +};
> +
> +static int dwc3_meson_g12a_get_phys(struct dwc3_meson_g12a *priv)
> +{
> + int i;
> +
> + for (i = 0 ; i < PHY_COUNT ; ++i) {
> + priv->phys[i] = devm_phy_optional_get(priv->dev, phy_names[i]);
> + if (!priv->phys[i])
> + continue;
> +
> + if (IS_ERR(priv->phys[i]))
> + return PTR_ERR(priv->phys[i]);
> +
> + if (i == USB3_HOST_PHY)
> + priv->usb3_ports++;
> + else
> + priv->usb2_ports++;
> + }
> +
> + dev_info(priv->dev, "USB2 ports: %d\n", priv->usb2_ports);
> + dev_info(priv->dev, "USB3 ports: %d\n", priv->usb3_ports);
> +
> + return 0;
> +}
> +
> +static enum phy_mode dwc3_meson_g12a_get_id(struct dwc3_meson_g12a *priv)
> +{
> + u32 reg;
> +
> + regmap_read(priv->regmap, USB_R5, &reg);
> +
> + if (reg & (USB_R5_ID_DIG_SYNC | USB_R5_ID_DIG_REG))
> + return PHY_MODE_USB_DEVICE;
> +
> + return PHY_MODE_USB_HOST;
> +}
> +
> +static int dwc3_meson_g12a_otg_mode_set(struct dwc3_meson_g12a *priv,
> + enum phy_mode mode)
> +{
> + int ret;
> +
> + if (!priv->phys[USB2_OTG_PHY])
> + return -EINVAL;
> +
> + if (mode == PHY_MODE_USB_HOST)
> + dev_info(priv->dev, "switching to Host Mode\n");
> + else
> + dev_info(priv->dev, "switching to Device Mode\n");
> +
> + if (priv->vbus) {
> + if (mode == PHY_MODE_USB_DEVICE)
> + ret = regulator_disable(priv->vbus);
> + else
> + ret = regulator_enable(priv->vbus);
> + if (ret)
> + return ret;
> + }
> +
> + priv->otg_phy_mode = mode;
> +
> + dwc3_meson_g12a_usb2_set_mode(priv, USB2_OTG_PHY, mode);
> +
> + dwc3_meson_g12a_usb_otg_apply_mode(priv);
> +
> + return 0;
> +}
> +
> +static int dwc3_meson_g12a_role_set(struct device *dev, enum usb_role role)
> +{
> + struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
> + enum phy_mode mode;
> +
> + if (role == USB_ROLE_NONE)
> + return 0;
> +
> + mode = (role == USB_ROLE_HOST) ? PHY_MODE_USB_HOST
> + : PHY_MODE_USB_DEVICE;
> +
> + if (mode == priv->otg_phy_mode)
> + return 0;
> +
> + return dwc3_meson_g12a_otg_mode_set(priv, mode);
> +}
> +
> +static enum usb_role dwc3_meson_g12a_role_get(struct device *dev)
> +{
> + struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
> +
> + return priv->otg_phy_mode == PHY_MODE_USB_HOST ?
> + USB_ROLE_HOST : USB_ROLE_DEVICE;
> +}
> +
> +static struct device *dwc3_meson_g12_find_child(struct device *dev,
> + const char *compatible)
> +{
> + struct platform_device *pdev;
> + struct device_node *np;
> +
> + np = of_get_compatible_child(dev->of_node, compatible);
> + if (!np)
> + return NULL;
> +
> + pdev = of_find_device_by_node(np);
> + of_node_put(np);
> + if (!pdev)
> + return NULL;
> +
> + return &pdev->dev;
> +}
> +
> +static int dwc3_meson_g12a_probe(struct platform_device *pdev)
> +{
> + struct dwc3_meson_g12a *priv;
> + struct device *dev = &pdev->dev;
> + struct device_node *np = dev->of_node;
> + void __iomem *base;
> + struct resource *res;
> + enum phy_mode otg_id;
> + int ret, i;
> +
> + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + base = devm_ioremap_resource(dev, res);
> + if (IS_ERR(base))
> + return PTR_ERR(base);
> +
> + priv->regmap = devm_regmap_init_mmio(dev, base,
> + &phy_meson_g12a_usb3_regmap_conf);
> + if (IS_ERR(priv->regmap))
> + return PTR_ERR(priv->regmap);
> +
> + priv->vbus = devm_regulator_get_optional(dev, "vbus");
> + if (IS_ERR(priv->vbus)) {
> + if (PTR_ERR(priv->vbus) == -EPROBE_DEFER)
> + return PTR_ERR(priv->vbus);
> + priv->vbus = NULL;
> + }
> +
> + priv->clk = devm_clk_get(dev, NULL);
> + if (IS_ERR(priv->clk))
> + return PTR_ERR(priv->clk);
> +
> + ret = clk_prepare_enable(priv->clk);
> + if (ret)
> + return ret;
> +
> + devm_add_action_or_reset(dev,
> + (void(*)(void *))clk_disable_unprepare,
> + priv->clk);
> +
> + platform_set_drvdata(pdev, priv);
> + priv->dev = dev;
> +
> + priv->reset = devm_reset_control_get(dev, NULL);
> + if (IS_ERR(priv->reset)) {
> + ret = PTR_ERR(priv->reset);
> + dev_err(dev, "failed to get device reset, err=%d\n", ret);
> + return ret;
> + }
> +
> + ret = reset_control_reset(priv->reset);
> + if (ret)
> + return ret;
> +
> + ret = dwc3_meson_g12a_get_phys(priv);
> + if (ret)
> + return ret;
> +
> + if (priv->vbus) {
> + ret = regulator_enable(priv->vbus);
> + if (ret)
> + return ret;
> + }
> +
> + /* Get dr_mode */
> + priv->otg_mode = usb_get_dr_mode(dev);
> +
> + dwc3_meson_g12a_usb_init(priv);
> +
> + /* Init PHYs */
> + for (i = 0 ; i < PHY_COUNT ; ++i) {
> + ret = phy_init(priv->phys[i]);
> + if (ret)
> + goto err_phys_power;
> + }
> +
> + /* Set PHY Power */
> + for (i = 0 ; i < PHY_COUNT ; ++i) {
> + ret = phy_power_on(priv->phys[i]);
> + if (ret)
> + goto err_phys_put;
> + }
> +
> + ret = of_platform_populate(np, NULL, NULL, dev);
> + if (ret) {
> + clk_disable_unprepare(priv->clk);
> + clk_put(priv->clk);
No need clk_put()
> +
> + goto err_phys_exit;
> + }
> +
> + /* Setup OTG mode corresponding to the ID pin */
> + if (priv->otg_mode == USB_DR_MODE_OTG) {
> + /* TOFIX Handle ID mode toggling via IRQ */
> + otg_id = dwc3_meson_g12a_get_id(priv);
> + if (otg_id != priv->otg_phy_mode) {
> + if (dwc3_meson_g12a_otg_mode_set(priv, otg_id))
> + dev_warn(dev, "Failed to switch OTG mode\n");
> + }
> + }
> +
> + /* Setup role switcher */
> + priv->switch_desc.usb2_port = dwc3_meson_g12_find_child(dev,
> + "snps,dwc3");
> + priv->switch_desc.udc = dwc3_meson_g12_find_child(dev, "snps,dwc2");
> + priv->switch_desc.allow_userspace_control = true;
> + priv->switch_desc.set = dwc3_meson_g12a_role_set;
> + priv->switch_desc.get = dwc3_meson_g12a_role_get;
> +
> + priv->role_switch = usb_role_switch_register(dev, &priv->switch_desc);
> + if (IS_ERR(priv->role_switch))
> + dev_warn(dev, "Unable to register Role Switch\n");
> +
> + pm_runtime_set_active(dev);
> + pm_runtime_enable(dev);
> + pm_runtime_get_sync(dev);
> +
> + return 0;
> +
> +err_phys_exit:
> + for (i = 0 ; i < PHY_COUNT ; ++i)
> + phy_exit(priv->phys[i]);
> +
> +err_phys_power:
> + for (i = 0 ; i < PHY_COUNT ; ++i)
> + phy_power_off(priv->phys[i]);
> +
> +err_phys_put:
> + for (i = 0 ; i < PHY_COUNT ; ++i)
> + phy_put(priv->phys[i]);
you get phy by devm_phy_optional_get(), no need call phy_put(),
> +
> + return ret;
> +}
> +
> +static int dwc3_meson_g12a_remove(struct platform_device *pdev)
> +{
> + struct dwc3_meson_g12a *priv = platform_get_drvdata(pdev);
> + struct device *dev = &pdev->dev;
> + int i;
> +
> + usb_role_switch_unregister(priv->role_switch);
> +
> + of_platform_depopulate(dev);
> +
> + for (i = 0 ; i < PHY_COUNT ; ++i) {
> + phy_power_off(priv->phys[i]);
> + phy_exit(priv->phys[i]);
> + phy_put(priv->phys[i]);
here, and remove others if have.
> + }
> +
> + pm_runtime_disable(dev);
> + pm_runtime_put_noidle(dev);
> + pm_runtime_set_suspended(dev);
> +
> + return 0;
> +}
> +
> +static int __maybe_unused dwc3_meson_g12a_runtime_suspend(struct device *dev)
> +{
> + struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
> +
> + clk_disable(priv->clk);
> +
> + return 0;
> +}
> +
> +static int __maybe_unused dwc3_meson_g12a_runtime_resume(struct device *dev)
> +{
> + struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
> +
> + return clk_enable(priv->clk);
> +}
> +
> +static int __maybe_unused dwc3_meson_g12a_suspend(struct device *dev)
> +{
> + struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
> + int i;
> +
> + for (i = 0 ; i < PHY_COUNT ; ++i)
> + phy_exit(priv->phys[i]);
> +
> + reset_control_assert(priv->reset);
> +
> + return 0;
> +}
> +
> +static int __maybe_unused dwc3_meson_g12a_resume(struct device *dev)
> +{
> + struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
> + int i, ret;
> +
> + reset_control_deassert(priv->reset);
> +
> + dwc3_meson_g12a_usb_init(priv);
> +
> + /* Init PHYs */
> + for (i = 0 ; i < PHY_COUNT ; ++i) {
> + ret = phy_init(priv->phys[i]);
> + if (ret)
> + return ret;
> + }
Do you need power on phys?
> +
> + return 0;
> +}
> +
> +static const struct dev_pm_ops dwc3_meson_g12a_dev_pm_ops = {
> + SET_SYSTEM_SLEEP_PM_OPS(dwc3_meson_g12a_suspend, dwc3_meson_g12a_resume)
> + SET_RUNTIME_PM_OPS(dwc3_meson_g12a_runtime_suspend,
> + dwc3_meson_g12a_runtime_resume, NULL)
> +};
> +
> +static const struct of_device_id dwc3_meson_g12a_match[] = {
> + { .compatible = "amlogic,meson-g12a-usb-ctrl" },
> + { /* Sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, dwc3_meson_g12a_match);
> +
> +static struct platform_driver dwc3_meson_g12a_driver = {
> + .probe = dwc3_meson_g12a_probe,
> + .remove = dwc3_meson_g12a_remove,
> + .driver = {
> + .name = "dwc3-meson-g12a",
> + .of_match_table = dwc3_meson_g12a_match,
> + .pm = &dwc3_meson_g12a_dev_pm_ops,
> + },
> +};
> +
> +module_platform_driver(dwc3_meson_g12a_driver);
> +MODULE_LICENSE("GPL v2");
> +MODULE_DESCRIPTION("Amlogic Meson G12A USB Glue Layer");
> +MODULE_AUTHOR("Neil Armstrong <narmstrong@baylibre.com>");


\
 
 \ /
  Last update: 2019-03-19 02:58    [W:0.206 / U:0.556 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site