lkml.org 
[lkml]   [2019]   [Mar]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH 6/9] arm64: dts: meson: g12a: Add UART A, B & C nodes and pins
Hi Neil,

On Thu, Mar 7, 2019 at 4:15 PM Neil Armstrong <narmstrong@baylibre.com> wrote:
>
> This patch adds the 2 UART nodes in the EE power domain with the corresponding
> pinctrl nodes.
there are 3 UART controllers in the EE power domain

> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
> ---
> arch/arm64/boot/dts/amlogic/meson-g12a.dtsi | 82 +++++++++++++++++++++
> 1 file changed, 82 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
> index 2a700bb45d04..50e2cd36e08b 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-g12a.dtsi
> @@ -113,6 +113,61 @@
> #gpio-cells = <2>;
> gpio-ranges = <&periphs_pinctrl 0 0 86>;
> };
> +
> + uart_a_pins: uart_a {
(this applies to all new nodes)
we started using dashes for the node names for new pin definitions on
the GX SoCs.
I don't remember where it was discussed exactly but I think this was
requested from Rob

since G12A is a new SoC we should do it "right" from the beginning

[...]
> + uart_ao_a_c_pins: uart_ao_a_c {
> + mux {
> + groups = "uart_ao_a_rx_c",
> + "uart_ao_a_tx_c";
> + function = "uart_ao_a_c";
> + bias-disable;
> + };
> + };
I'm fine with this part if you mention it in the subject and/or the description
uart_ao_a_c routes two pins from bank C (from the EE domain) to the
uart_AO controller (from the AO domain)

> + uart_b_pins: uart_b {
> + mux {
> + groups = "uart_b_tx",
> + "uart_b_rx";
> + function = "uart_b";
> + bias-disable;
> + };
> + };
> +
> + uart_c_pins: uart_c {
> + mux {
> + groups = "uart_c_tx",
> + "uart_c_rx";
> + function = "uart_c";
> + bias-disable;
> + };
> + };
> +
> + uart_c_cts_rts_pins: uart_c_cts_rts {
> + mux {
> + groups = "uart_c_cts",
> + "uart_c_rts";
> + function = "uart_c";
> + bias-disable;
> + };
> + };
> + };
> };
>
> hiu: bus@3c000 {
> @@ -256,6 +311,33 @@
> compatible = "amlogic,meson-g12a-clk-measure";
> reg = <0x0 0x18000 0x0 0x10>;
> };
> +
> + uart_C: serial@22000 {
> + compatible = "amlogic,meson-gx-uart";
> + reg = <0x0 0x22000 0x0 0x18>;
> + interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>;
> + clocks = <&xtal>, <&clkc CLKID_UART1>, <&xtal>;
does uart_C really use CLKID_UART1? on GX uart_C uses CLKID_UART2


Regards
Martin

\
 
 \ /
  Last update: 2019-03-15 22:26    [W:0.152 / U:3.264 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site