lkml.org 
[lkml]   [2019]   [Mar]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2 2/2] mmc: sdhci-omap: Don't finish_mrq() on a command error during tuning
From
Date
Hi Adrian,

On 3/6/2019 5:39 PM, Adrian Hunter wrote:
> On 1/03/19 10:38 AM, Faiz Abbas wrote:
>> commit 5b0d62108b46 ("mmc: sdhci-omap: Add platform specific reset
>> callback") skips data resets during tuning operation. Because of this,
>> a data error or data finish interrupt might still arrive after a command
>> error has been handled and the mrq ended. This ends up with a "mmc0: Got
>> data interrupt 0x00000002 even though no data operation was in progress"
>> error message.
>>
>> Fix this by adding a platform specific callback for command errors. Mark
>> the mrq as a failure but wait for a data interrupt instead of calling
>> finish_mrq().
>>
>> Fixes: 5b0d62108b46 ("mmc: sdhci-omap: Add platform specific reset
>> callback")
>> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
>> ---
>> drivers/mmc/host/sdhci-omap.c | 24 ++++++++++++++++++++++++
>> 1 file changed, 24 insertions(+)
>>
>> diff --git a/drivers/mmc/host/sdhci-omap.c b/drivers/mmc/host/sdhci-omap.c
>> index b1a66ca3821a..67b361a403bc 100644
>> --- a/drivers/mmc/host/sdhci-omap.c
>> +++ b/drivers/mmc/host/sdhci-omap.c
>> @@ -797,6 +797,29 @@ void sdhci_omap_reset(struct sdhci_host *host, u8 mask)
>> sdhci_reset(host, mask);
>> }
>>
>> +void sdhci_omap_cmd_err(struct sdhci_host *host, u32 intmask, u32 *intmask_p)
>> +{
>> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>> + struct sdhci_omap_host *omap_host = sdhci_pltfm_priv(pltfm_host);
>> +
>> + if (omap_host->is_tuning) {
>> + /*
>> + * Since we are not resetting data lines during tuning
>> + * operation, data error or data complete interrupts
>> + * might still arrive. Mark this request as a failure
>> + * but still wait for the data interrupt
>> + */
>> + if (intmask & SDHCI_INT_TIMEOUT)
>> + host->cmd->error = -ETIMEDOUT;
>> + else
>> + host->cmd->error = -EILSEQ;
>> +
>> + sdhci_finish_command(host);
>> + } else {
>> + sdhci_cmd_err(host, intmask, intmask_p);
>> + }
>> +}
>
> Could this be done by the existing ->irq() callback? i.e. mask the error
> bits in intmask (have to write them back to SDHCI_INT_STATUS also) but set
> cmd->error.
>

It is possible but I really don't want the callback to be unnecessarily
called for every single interrupt that happens. I think we should only
use the callback in the case of an actual error interrupt :-)

Thanks,
Faiz

\
 
 \ /
  Last update: 2019-03-12 18:35    [W:2.446 / U:0.024 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site