lkml.org 
[lkml]   [2019]   [Mar]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCHv2 2/5] Documentation: dt: edac: Add Stratix10 Peripheral bindings
On Wed, Feb 27, 2019 at 11:27:22AM -0600, thor.thayer@linux.intel.com wrote:
> From: Thor Thayer <thor.thayer@linux.intel.com>
>
> Add peripheral bindings for Stratix10 EDAC to capture
> the differences between the ARM64 and ARM32 architecture.

What's the difference? Sounds like 2 different chips, so Stratix10 or
s10 is not specific enough perhaps.

>
> Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
> ---
> v2 No change
> ---
> .../devicetree/bindings/edac/socfpga-eccmgr.txt | 106 +++++++++++++++++++++
> 1 file changed, 106 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/edac/socfpga-eccmgr.txt b/Documentation/devicetree/bindings/edac/socfpga-eccmgr.txt
> index a0ac50e15912..a0fa80c53d2a 100644
> --- a/Documentation/devicetree/bindings/edac/socfpga-eccmgr.txt
> +++ b/Documentation/devicetree/bindings/edac/socfpga-eccmgr.txt
> @@ -258,6 +258,49 @@ Required Properties:
> - compatible : Should be "altr,sdram-edac-s10"
> - interrupts : Should be single bit error interrupt.
>
> +On-Chip RAM ECC
> +Required Properties:
> +- compatible : Should be "altr,socfpga-s10-ocram-ecc"
> +- reg : Address and size for ECC block registers.
> +- altr,ecc-parent : phandle to parent OCRAM node.
> +- interrupts : Should be single bit error interrupt.
> +
> +Ethernet FIFO ECC
> +Required Properties:
> +- compatible : Should be "altr,socfpga-s10-eth-mac-ecc"
> +- reg : Address and size for ECC block registers.
> +- altr,ecc-parent : phandle to parent Ethernet node.
> +- interrupts : Should be single bit error interrupt.
> +
> +NAND FIFO ECC
> +Required Properties:
> +- compatible : Should be "altr,socfpga-s10-nand-ecc"
> +- reg : Address and size for ECC block registers.
> +- altr,ecc-parent : phandle to parent NAND node.
> +- interrupts : Should be single bit error interrupt.
> +
> +DMA FIFO ECC
> +Required Properties:
> +- compatible : Should be "altr,socfpga-s10-dma-ecc"
> +- reg : Address and size for ECC block registers.
> +- altr,ecc-parent : phandle to parent DMA node.
> +- interrupts : Should be single bit error interrupt.
> +
> +USB FIFO ECC
> +Required Properties:
> +- compatible : Should be "altr,socfpga-s10-usb-ecc"
> +- reg : Address and size for ECC block registers.
> +- altr,ecc-parent : phandle to parent USB node.
> +- interrupts : Should be single bit error interrupt.
> +
> +SDMMC FIFO ECC
> +Required Properties:
> +- compatible : Should be "altr,socfpga-s10-sdmmc-ecc"
> +- reg : Address and size for ECC block registers.
> +- altr,ecc-parent : phandle to parent SD/MMC node.
> +- interrupts : Should be single bit error interrupt for port A
> + and then single bit error interrupt for port B.
> +
> Example:
>
> eccmgr {
> @@ -274,4 +317,67 @@ Example:
> compatible = "altr,sdram-edac-s10";
> interrupts = <16 IRQ_TYPE_LEVEL_HIGH>;
> };
> +
> + ocram-ecc@ff8cc000 {
> + compatible = "altr,socfpga-s10-ocram-ecc";
> + reg = <ff8cc000 0x100>;
> + altr,ecc-parent = <&ocram>;
> + interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + emac0-rx-ecc@ff8c0000 {
> + compatible = "altr,socfpga-s10-eth-mac-ecc";
> + reg = <0xff8c0000 0x100>;
> + altr,ecc-parent = <&gmac0>;
> + interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + emac0-tx-ecc@ff8c0400 {
> + compatible = "altr,socfpga-s10-eth-mac-ecc";
> + reg = <0xff8c0400 0x100>;
> + altr,ecc-parent = <&gmac0>;
> + interrupts = <5 IRQ_TYPE_LEVEL_HIGH>'
> + };
> +
> + nand-buf-ecc@ff8c8000 {
> + compatible = "altr,socfpga-s10-nand-ecc";
> + reg = <0xff8c8000 0x100>;
> + altr,ecc-parent = <&nand>;
> + interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + nand-rd-ecc@ff8c8400 {
> + compatible = "altr,socfpga-s10-nand-ecc";
> + reg = <0xff8c8400 0x100>;
> + altr,ecc-parent = <&nand>;
> + interrupts = <13 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + nand-wr-ecc@ff8c8800 {
> + compatible = "altr,socfpga-s10-nand-ecc";
> + reg = <0xff8c8800 0x100>;
> + altr,ecc-parent = <&nand>;
> + interrupts = <12 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + dma-ecc@ff8c9000 {
> + compatible = "altr,socfpga-s10-dma-ecc";
> + reg = <0xff8c9000 0x100>;
> + altr,ecc-parent = <&pdma>;
> + interrupts = <10 IRQ_TYPE_LEVEL_HIGH>;
> +
> + usb0-ecc@ff8c4000 {
> + compatible = "altr,socfpga-s10-usb-ecc";
> + reg = <0xff8c4000 0x100>;
> + altr,ecc-parent = <&usb0>;
> + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + sdmmc-ecc@ff8c8c00 {
> + compatible = "altr,socfpga-s10-sdmmc-ecc";
> + reg = <0xff8c8c00 0x100>;
> + altr,ecc-parent = <&mmc>;
> + interrupts = <14 IRQ_TYPE_LEVEL_HIGH>,
> + <15 IRQ_TYPE_LEVEL_HIGH>;
> + };
> };
> --
> 2.7.4
>

\
 
 \ /
  Last update: 2019-03-12 17:05    [W:0.107 / U:0.212 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site