lkml.org 
[lkml]   [2019]   [Feb]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH] mtd: rawnand: call onfi_fill_data_interface() once again after nand_detect
On Thu, Feb 7, 2019 at 7:16 PM Miquel Raynal <miquel.raynal@bootlin.com> wrote:
>
> Hi Masahiro,
>
> Masahiro Yamada <yamada.masahiro@socionext.com> wrote on Thu, 7 Feb
> 2019 18:57:56 +0900:
>
> > nand_scan_ident() calls onfi_fill_data_interface() at its entry
> > to set up the initial timing parameters.
> >
> > The timing parameters are needed not only for ->setup_data_interface(),
> > but also for giving the correct delay to NAND_OP_WAIT_RDY, for example.
> >
> > If the driver sets the NAND_KEEP_TIMINGS flag, or does not support
> > ->setup_data_interface() hook, those parameters will never updated.
>
> ^ be

Will fix (if v2 is welcome)


> >
> > Before nand_detect(), we never know whether the chip is ONFi or not.
> > So, onfi_fill_data_interface() has to assume the worst case, i.e.
> > non-ONFi.
>
> s/ONFi/ONFI/?

Will fix.

Looks like I was misunderstanding
maybe because the letter 'I' in the logo
(http://www.onfi.org/)
looks like a lowercase...




>
> >
> > After nand_detect(), if the chip turns out to be ONFi-compliant,
> > we can optimize tPROG_max, tBERS_max, etc.
> >
> > Call onfi_fill_data_interface() once again.
>
> Sorry but I don't get why this is needed as there is the same call at
> the top of this function. Can you be more specific on where/when the
> missing call produces a failure?


onfi_fill_data_interface() sets different values
for tPROG_max, tBER_max, tR_max, tCCS_min
depending on whether the chip is ONFI or not.

For the first call, onfi_fill_data_interface()
chooses the else-part since we never know
the chip specification at this point.

If we call onfi_fill_data_interface() once again
after nand_detect(), it may choose the if-part.


If a driver supports ->setup_data_interface(),
nand_init_data_interface() will set the optimal
timing parameters anyway.

But, if a driver does not support ->setup_data_interface(),
it will not happen since nand_has_setup_data_iface() returns false.





> >
> > Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
> > ---
> >
> > drivers/mtd/nand/raw/nand_base.c | 3 +++
> > 1 file changed, 3 insertions(+)
> >
> > diff --git a/drivers/mtd/nand/raw/nand_base.c b/drivers/mtd/nand/raw/nand_base.c
> > index 9b3d7ff..35e543c 100644
> > --- a/drivers/mtd/nand/raw/nand_base.c
> > +++ b/drivers/mtd/nand/raw/nand_base.c
> > @@ -5040,6 +5040,9 @@ static int nand_scan_ident(struct nand_chip *chip, unsigned int maxchips,
> >
> > nand_deselect_target(chip);
> >
> > + /* If the chip turns out ONFi, we can optimize timing parameters. */
> > + onfi_fill_data_interface(chip, NAND_SDR_IFACE, 0);
> > +
> > /* Check for a chip array */
> > for (i = 1; i < maxchips; i++) {
> > u8 id[2];
>
>
> Thanks,
> Miquèl



--
Best Regards
Masahiro Yamada

\
 
 \ /
  Last update: 2019-02-07 11:49    [W:0.090 / U:0.344 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site