lkml.org 
[lkml]   [2019]   [Feb]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH 1/2] mtd: spi-nor: Add support for EN25Q80A
Date
Hi Tudor,

On 03.02.19 14:33, Tudor.Ambarus@microchip.com wrote:
> Hi, Frieder,
>
> On 01/23/2019 09:56 AM, Schrempf Frieder wrote:
>> From: Frieder Schrempf <frieder.schrempf@kontron.de>
>>
>> This adds support for the EON EN25Q80A, a 8Mb SPI NOR chip.
>
> I would suggest to specify who is using this flash and how did you test it. This
> way we will not end up with support for flashes that are not actually used.

Ok. The flash is used by a board that I plan to upstream. Maybe I should
just resubmit this together with the actual board support patches?

Likewise for my other patch (MX25V8035F), this is for another board I
plan to upstream soon.

>
>>
>> Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
>> ---
>> drivers/mtd/spi-nor/spi-nor.c | 2 ++
>> 1 file changed, 2 insertions(+)
>>
>> diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
>> index 6e13bbd1aaa5..aa8a04293a25 100644
>> --- a/drivers/mtd/spi-nor/spi-nor.c
>> +++ b/drivers/mtd/spi-nor/spi-nor.c
>> @@ -1737,6 +1737,8 @@ static const struct flash_info spi_nor_ids[] = {
>> /* EON -- en25xxx */
>> { "en25f32", INFO(0x1c3116, 0, 64 * 1024, 64, SECT_4K) },
>> { "en25p32", INFO(0x1c2016, 0, 64 * 1024, 64, 0) },
>> + { "en25q80a", INFO(0x1c3014, 0, 64 * 1024, 16,
>> + SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
>
> I'm reading EN25Q80A Rev. H, Issue Date: 2012/10/23
> datasheet. I don't see the bfpt table described, so probably it doesn't support
> it. The flash advertises SPINOR_OP_READ_1_4_4 (0xeb), but not
> SPINOR_OP_READ_1_1_4 (0x6b). In spi_nor_init_params(), when SPI_NOR_QUAD_READ is
> set, we assume that SNOR_HWCAPS_READ_1_1_4 is supported, so we will use 0x6b for
> quad reads. I can't see how the flash works with 0x6b, unless there is a bfpt
> table that indicates support for 0xebh.
>
> If it does support bfpt, set just SECT_4K | SPI_NOR_DUAL_READ, the latter will
> trigger the bfpt parsing.

Thanks for explaining this. I missed the point, that SPI_NOR_QUAD_READ
actually requires support for SPINOR_OP_READ_1_1_4.

>
> If you will resubmit, please order the entry in alphabetical order, by name.

Ok.

Thanks,
Frieder
\
 
 \ /
  Last update: 2019-02-07 11:07    [W:0.102 / U:0.084 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site