lkml.org 
[lkml]   [2019]   [Feb]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [RFC 5/5] arm64: dts: imx8mq: Add the opp table and the cpu-supply nodes
From
Date
Am Donnerstag, den 14.02.2019, 18:26 +0100 schrieb Lucas Stach:
> Am Donnerstag, den 14.02.2019, 17:18 +0000 schrieb Abel Vesa:
> > On 19-02-14 16:50:28, Lucas Stach wrote:
> > > Hi Abel
> > >
> > > Am Mittwoch, den 13.02.2019, 19:05 +0000 schrieb Abel Vesa:
> > > > Add the opp table containing only non over drive opps.
> > > > Also add the cpu-supply nodes for the A53 cores in the EVK
> > > > board.
> > > >
> > > > Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
> > > > ---
> > > >  arch/arm64/boot/dts/freescale/imx8mq-evk.dts | 17
> > > > +++++++++++++++++
> > > >  arch/arm64/boot/dts/freescale/imx8mq.dtsi    | 23
> > > > +++++++++++++++++++++++
> > > >  2 files changed, 40 insertions(+)
> > > >
> > > > diff --git a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
> > > > b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
> > > > index 54737bf..114359e 100644
> > > > --- a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
> > > > +++ b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
> > > > @@ -31,6 +31,23 @@
> > > >   gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> > > >   enable-active-high;
> > > >   };
> > > > +
> > > > +};
> > > > +
> > > > +&A53_0 {
> > > > + cpu-supply = <&sw1a_reg>;
> > > > +};
> > > > +
> > > > +&A53_1 {
> > > > + cpu-supply = <&sw1a_reg>;
> > > > +};
> > > > +
> > > > +&A53_2 {
> > > > + cpu-supply = <&sw1a_reg>;
> > > > +};
> > > > +
> > > > +&A53_3 {
> > > > + cpu-supply = <&sw1a_reg>;
> > > >  };
> > >
> > > This should be a separate patch.
> > >
> >
> > OK, will send as separate patches in the next version.
> >
> > > And AFAICS this is wrong, sw1a on the MX8M-EVK is the GPU supply,
> > > the
> > > CPU is supplied by a dedicated switcher that is controlled via a
> > > GPIO.
> > >
> >
> > Hmm, I think you're right. At least this is what the following
> > document says.
> >
> > https://www.mouser.com/ds/2/302/IMX8MDQLQEVKHUG-1280333.pdf
> >
> > So I guess this means there will not be any cpu-supply properties. 
>
> There is a variable voltage CPU supply, but you need to model it as a
> gpio-regulator in the DT, it's not part of the PMIC provided rails.

In the schematics it's the line called PWM_LED (actually it's just
GPIO1_IO13) that controls the voltage. This changes the feedback of the
DCDC switcher, so it can toggle between 0.9V and 1.0V.

Regards,
Lucas

\
 
 \ /
  Last update: 2019-02-14 18:33    [W:1.179 / U:0.252 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site