lkml.org 
[lkml]   [2019]   [Feb]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2 0/2] drivers: devfreq: fix and optimize workqueue mechanism
From
Date
Hi Lukasz,

On 19. 2. 12. 오후 9:05, Lukasz Luba wrote:
> Hi Chanwoo
>
> On 2/12/19 6:46 AM, Chanwoo Choi wrote:
>> Hi Lukasz,
>>
>> On 19. 2. 12. 오전 12:30, Lukasz Luba wrote:
>>> This patch set changes workqueue related features in devfreq framework.
>>> First patch switches to delayed work instead of deferred.
>>> The second switches to regular system work and deletes custom 'devfreq'.
>>>
>>> Using deferred work in this context might harm the system performance.
>>> When the CPU enters idle, deferred work is not fired. The devfreq device's
>>> utilization does not have to be connected with a particular CPU.
>>> The drivers for GPUs, Network on Chip, cache L3 rely on devfreq governor.
>>> They all are missing opportunity to check the HW state and react when
>>> the deferred work is not fired.
>>> A corner test case, when Dynamic Memory Controller is utilized by CPUs running
>>> on full speed, might show x5 worse performance if the crucial CPU is in idle.
>>
>> The devfreq framework keeps the balancing between performance
>> and power-consumption. It is wrong to focus on only either
>> performance or power.
> IMO it just does not work, please see my explanation below.
>>
>> This cover-letter focus on the only performance without any power-consumption
>> disadvantages. It is easy to raise the performance with short sampling rate
>> with polling modes. To get the performance, it is good as short as possible
>> of period.
> The cover-letter mentioned about missing functionality. The interface
> has 'polling_ms' field, which driver developer would assume works.
> I have test cases where it would not be called for seconds or even
> never.
> In your driver drivers/devfreq/exynos-bus.c polling_ms = 50
> The driver is controlling many devices including Network-on-Chip (NOC).
> It is using 'simple_ondemand' governor. When it is missing opportunity
> to change the frequency, it can either harm the performance or power
> consumption, depending of the frequency the device stuck on.

Almost everyone knew that DVFS governor is never perfect in the linux kernel.
I don't want to discuss it with this too generic opinion which doesn't
include the real measured data.

>
>>
>> Sometimes, when cpu is idle, the device might require the busy state.
>> It is very difficult to catch the always right timing between them.
> I will try to address them in the next patch set.
>>
>> Also, this patch cannot prevent the unneeded wakeup from idle state.

Please answer this question.

When release the real mobile product like galaxy phone,
it is very important issue to remove the unneeded wakeup on idle state.


>> Apparently, it only focuses on performance without considering
>> the power-consumption disadvantage. In the embedded device,
>> the power-consumption is very important point. We can not ignore
>> the side effect.
> Power consumption is important, but we cannot rely on randomness
> when we develop core features in a framework.

Sure, I agree that as I commented, the devfreq framework keep
the balancing between performance and power-consumption.

Instead, this patch only focus on the performance without considering
the power-consumption side-effect.

>>
>> Always, I hope to improve the devfreq framwork more that older.
>> But, frankly, it is difficult to agree because it only consider
>> the performance without considering the side-effect.
>>
>> The power management framework always have to consider
>> the power-consumption issue. This point is always true.
> I do agree that the power vs. performance trade-off must be considered
> in the devfreq framework. I have developed 2 additional patches and

You should only mention the posted patches on mailing list.

> I am going to post them today (you can now check them on Tizen gerrit,
> change 198160).

It is not good to mention the some specific gerrit. I just only review
the patches on mailing list. First of all, please answer the question
on above

>
> We cannot simply pin the *device* load with *CPU* load or idle state.
> It is not an implication.
> The device like GPU, NoC or Dynamic Memory Controller can have
> completely different utilization (i.e in Exynos the GPU is connected
> to DDR memory through NoC and DMC).

In order to get the high performance, the performance of GPU depends on CPU.
h/w have depended on them tightly coupled. So, it is not easy to show
the just relationship between them. We need the comprehensive measured data
for both performance and power-consumption on all cases without the corner cases.

> Some developers who use OpenCL on GPU might be interested in this
> improvement.>
> Thank you for participating in the discussion on this issue.
> It will need more development and iterations.
> In my opinion currently there is one bug in the devfreq and one missing
> feature to solve.
>
> Regards,
> Lukasz
>
>>
>>>
>>> Changes:
>>> v2:
>>> - single patch split into two
>>> - added cover letter
>>>
>>> link for the previous version and discussion:
>>> https://marc.info/?l=linux-pm&m=154904631226997&w=2
>>>
>>> Regards,
>>> Lukasz Luba
>>>
>>> Lukasz Luba (2):
>>> drivers: devfreq: change devfreq workqueue mechanism
>>> drivers: devfreq: change deferred work into delayed
>>>
>>> drivers/devfreq/devfreq.c | 27 +++++++--------------------
>>> 1 file changed, 7 insertions(+), 20 deletions(-)
>>>
>>
>>
>
>


--
Best Regards,
Chanwoo Choi
Samsung Electronics

\
 
 \ /
  Last update: 2019-02-13 02:11    [W:0.146 / U:0.268 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site