Messages in this thread Patch in this message | | | From | Sandeep Maheswaram <> | Subject | [PATCH v2 3/3] dt-bindings: phy: qcom-qusb2: Add SC7180 QUSB2 phy support | Date | Thu, 5 Dec 2019 10:11:21 +0530 |
| |
Add QUSB2 phy entries for SC7180 in device tree bindings.
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org> --- Documentation/devicetree/bindings/phy/qcom-qusb2-phy.yaml | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-)
diff --git a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.yaml b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.yaml index 3ef94bc..5eff9016 100644 --- a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.yaml +++ b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.yaml @@ -18,6 +18,7 @@ properties: enum: - qcom,msm8996-qusb2-phy - qcom,msm8998-qusb2-phy + - qcom,sc7180-qusb2-phy - qcom,sdm845-qusb2-phy reg: @@ -66,7 +67,7 @@ properties: It is a 6 bit value that specifies offset to be added to PHY refgen RESCODE via IMP_CTRL1 register. It is a PHY tuning parameter that may vary for different boards of same SOC. - This property is applicable to only QUSB2 v2 PHY (sdm845). + This property is applicable to only QUSB2 v2 PHY (sc7180, sdm845). $ref: /schemas/types.yaml#/definitions/uint32 qcom,hstx-trim-value: @@ -75,7 +76,7 @@ properties: output current. Possible range is - 15mA to 24mA (stepsize of 600 uA). See dt-bindings/phy/phy-qcom-qusb2.h for applicable values. - This property is applicable to only QUSB2 v2 PHY (sdm845). + This property is applicable to only QUSB2 v2 PHY (sc7180, sdm845). Default value is 22.2mA for sdm845. $ref: /schemas/types.yaml#/definitions/uint32 @@ -84,7 +85,7 @@ properties: It is a 2 bit value that specifies pre-emphasis level. Possible range is 0 to 15% (stepsize of 5%). See dt-bindings/phy/phy-qcom-qusb2.h for applicable values. - This property is applicable to only QUSB2 v2 PHY (sdm845). + This property is applicable to only QUSB2 v2 PHY (sc7180, sdm845). Default value is 10% for sdm845. $ref: /schemas/types.yaml#/definitions/uint32 @@ -94,7 +95,7 @@ properties: pre-emphasis (specified using qcom,preemphasis-level) must be in effect. Duration could be half-bit of full-bit. See dt-bindings/phy/phy-qcom-qusb2.h for applicable values. - This property is applicable to only QUSB2 v2 PHY (sdm845). + This property is applicable to only QUSB2 v2 PHY (sc7180, sdm845). Default value is full-bit width for sdm845. $ref: /schemas/types.yaml#/definitions/uint32 -- QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
| |