lkml.org 
[lkml]   [2019]   [Dec]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 2/2] usbip: Fix error path of vhci_recv_ret_submit()
On Thu, Dec 12, 2019 at 10:54:08AM -0500, Alan Stern wrote:
> On Thu, 12 Dec 2019, Suwan Kim wrote:
>
> > If a transaction error happens in vhci_recv_ret_submit(), event
> > handler closes connection and changes port status to kick hub_event.
> > Then hub tries to flush the endpoint URBs, but that causes infinite
> > loop between usb_hub_flush_endpoint() and vhci_urb_dequeue() because
> > "vhci_priv" in vhci_urb_dequeue() was already released by
> > vhci_recv_ret_submit() before a transmission error occurred. Thus,
> > vhci_urb_dequeue() terminates early and usb_hub_flush_endpoint()
> > continuously calls vhci_urb_dequeue().
> >
> > The root cause of this issue is that vhci_recv_ret_submit()
> > terminates early without giving back URB when transaction error
> > occurs in vhci_recv_ret_submit(). That causes the error URB to still
> > be linked at endpoint list without “vhci_priv".
> >
> > So, in the case of trasnaction error in vhci_recv_ret_submit(),
> > unlink URB from the endpoint, insert proper error code in
> > urb->status and give back URB.
> >
> > Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
> > Signed-off-by: Suwan Kim <suwan.kim027@gmail.com>
> > ---
> > drivers/usb/usbip/vhci_rx.c | 13 +++++++++----
> > 1 file changed, 9 insertions(+), 4 deletions(-)
> >
> > diff --git a/drivers/usb/usbip/vhci_rx.c b/drivers/usb/usbip/vhci_rx.c
> > index 33f8972ba842..dc26acad6baf 100644
> > --- a/drivers/usb/usbip/vhci_rx.c
> > +++ b/drivers/usb/usbip/vhci_rx.c
> > @@ -77,16 +77,21 @@ static void vhci_recv_ret_submit(struct vhci_device *vdev,
> > usbip_pack_pdu(pdu, urb, USBIP_RET_SUBMIT, 0);
> >
> > /* recv transfer buffer */
> > - if (usbip_recv_xbuff(ud, urb) < 0)
> > - return;
> > + if (usbip_recv_xbuff(ud, urb) < 0) {
> > + urb->status = -EPIPE;
> > + goto error;
> > + }
> >
> > /* recv iso_packet_descriptor */
> > - if (usbip_recv_iso(ud, urb) < 0)
> > - return;
> > + if (usbip_recv_iso(ud, urb) < 0) {
> > + urb->status = -EPIPE;
> > + goto error;
> > + }
>
> -EPIPE is used for STALL. The appropriate error code for transaction
> error would be -EPROTO (or -EILSEQ or -ETIME, but people seem to be
> settling on -EPROTO).

Thanks for the feedback. I will fix it :)

Regards,
Suwan Kim

\
 
 \ /
  Last update: 2019-12-13 03:04    [W:0.047 / U:1.732 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site