lkml.org 
[lkml]   [2019]   [Nov]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 2/3] dt-bindings: usb: qcom,dwc3: Convert USB DWC3 bindings
Date
Convert USB DWC3 bindings to DT schema format using json-schema.

Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
---
.../devicetree/bindings/usb/qcom,dwc3.txt | 104 --------------
.../devicetree/bindings/usb/qcom,dwc3.yaml | 155 +++++++++++++++++++++
2 files changed, 155 insertions(+), 104 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/usb/qcom,dwc3.txt
create mode 100644 Documentation/devicetree/bindings/usb/qcom,dwc3.yaml

diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt
deleted file mode 100644
index cb695aa..0000000
--- a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt
+++ /dev/null
@@ -1,104 +0,0 @@
-Qualcomm SuperSpeed DWC3 USB SoC controller
-
-Required properties:
-- compatible: Compatible list, contains
- "qcom,dwc3"
- "qcom,msm8996-dwc3" for msm8996 SOC.
- "qcom,msm8998-dwc3" for msm8998 SOC.
- "qcom,sdm845-dwc3" for sdm845 SOC.
-- reg: Offset and length of register set for QSCRATCH wrapper
-- power-domains: specifies a phandle to PM domain provider node
-- clocks: A list of phandle + clock-specifier pairs for the
- clocks listed in clock-names
-- clock-names: Should contain the following:
- "core" Master/Core clock, have to be >= 125 MHz for SS
- operation and >= 60MHz for HS operation
- "mock_utmi" Mock utmi clock needed for ITP/SOF generation in
- host mode. Its frequency should be 19.2MHz.
- "sleep" Sleep clock, used for wakeup when USB3 core goes
- into low power mode (U3).
-
-Optional clocks:
- "iface" System bus AXI clock.
- Not present on "qcom,msm8996-dwc3" compatible.
- "cfg_noc" System Config NOC clock.
- Not present on "qcom,msm8996-dwc3" compatible.
-- assigned-clocks: Should be:
- MOCK_UTMI_CLK
- MASTER_CLK
-- assigned-clock-rates: Should be:
- 19.2Mhz (192000000) for MOCK_UTMI_CLK
- >=125Mhz (125000000) for MASTER_CLK in SS mode
- >=60Mhz (60000000) for MASTER_CLK in HS mode
-
-Optional properties:
-- resets: Phandle to reset control that resets core and wrapper.
-- interrupts: specifies interrupts from controller wrapper used
- to wakeup from low power/susepnd state. Must contain
- one or more entry for interrupt-names property
-- interrupt-names: Must include the following entries:
- - "hs_phy_irq": The interrupt that is asserted when a
- wakeup event is received on USB2 bus
- - "ss_phy_irq": The interrupt that is asserted when a
- wakeup event is received on USB3 bus
- - "dm_hs_phy_irq" and "dp_hs_phy_irq": Separate
- interrupts for any wakeup event on DM and DP lines
-- qcom,select-utmi-as-pipe-clk: if present, disable USB3 pipe_clk requirement.
- Used when dwc3 operates without SSPHY and only
- HS/FS/LS modes are supported.
-
-Required child node:
-A child node must exist to represent the core DWC3 IP block. The name of
-the node is not important. The content of the node is defined in dwc3.txt.
-
-Phy documentation is provided in the following places:
-Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt - USB3 QMP PHY
-Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt - USB2 QUSB2 PHY
-
-Example device nodes:
-
- hs_phy: phy@100f8800 {
- compatible = "qcom,qusb2-v2-phy";
- ...
- };
-
- ss_phy: phy@100f8830 {
- compatible = "qcom,qmp-v3-usb3-phy";
- ...
- };
-
- usb3_0: usb30@a6f8800 {
- compatible = "qcom,dwc3";
- reg = <0xa6f8800 0x400>;
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- interrupts = <0 131 0>, <0 486 0>, <0 488 0>, <0 489 0>;
- interrupt-names = "hs_phy_irq", "ss_phy_irq",
- "dm_hs_phy_irq", "dp_hs_phy_irq";
-
- clocks = <&gcc GCC_USB30_PRIM_MASTER_CLK>,
- <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
- <&gcc GCC_USB30_PRIM_SLEEP_CLK>;
- clock-names = "core", "mock_utmi", "sleep";
-
- assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
- <&gcc GCC_USB30_PRIM_MASTER_CLK>;
- assigned-clock-rates = <19200000>, <133000000>;
-
- resets = <&gcc GCC_USB30_PRIM_BCR>;
- reset-names = "core_reset";
- power-domains = <&gcc USB30_PRIM_GDSC>;
- qcom,select-utmi-as-pipe-clk;
-
- dwc3@10000000 {
- compatible = "snps,dwc3";
- reg = <0x10000000 0xcd00>;
- interrupts = <0 205 0x4>;
- phys = <&hs_phy>, <&ss_phy>;
- phy-names = "usb2-phy", "usb3-phy";
- dr_mode = "host";
- };
- };
-
diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml b/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
new file mode 100644
index 0000000..48ff9c5
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
@@ -0,0 +1,155 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/usb/qcom,dwc3.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm SuperSpeed DWC3 USB SoC controller
+
+maintainers:
+ - Manu Gautam <mgautam@codeaurora.org>
+
+properties:
+ compatible:
+ items:
+ - enum:
+ - qcom,msm8996-dwc3
+ - qcom,msm8998-dwc3
+ - qcom,sdm845-dwc3
+ - const: qcom,dwc3
+
+ reg:
+ description: Offset and length of register set for QSCRATCH wrapper
+ maxItems: 1
+
+ power-domains:
+ description: specifies a phandle to PM domain provider node
+ maxItems: 1
+
+ clocks:
+ description:
+ A list of phandle and clock-specifier pairs for the clocks
+ listed in clock-names.
+ maxItems: 5
+
+ clock-names:
+ maxItems: 5
+ items:
+ #Master/Core clock, have to be >= 125 MHz for SS operation
+ # and >= 60MHz for HS operation
+ - const: core
+ #Mock utmi clock needed for ITP/SOF generation in host mode.
+ #Its frequency should be 19.2MHz.
+ - const: mock_utmi
+ #Sleep clock, used for wakeup when USB3 core goes into low power mode (U3).
+ - const: sleep
+ #Optional:System bus AXI clock.Not present on "qcom,msm8996-dwc3" compatible.
+ - const: iface
+ #Optional:System Config NOC clock.Not present on "qcom,msm8996-dwc3" compatible.
+ - const: cfg_noc
+
+ assigned-clocks:
+ description:
+ Should be MOCK_UTMI_CLK and MASTER_CLK
+ maxItems: 2
+
+ assigned-clock-rates:
+ description:
+ Should be 19.2Mhz (192000000) for MOCK_UTMI_CLK
+ >=125Mhz (125000000) for MASTER_CLK in SS mode
+ >=60Mhz (60000000) for MASTER_CLK in HS mode
+ maxItems: 2
+
+ resets:
+ maxItems: 1
+ description: Phandle to reset control that resets core and wrapper.
+
+ interrupts:
+ description:
+ specifies interrupts from controller wrapper used
+ to wakeup from low power/suspend state.Must contain
+ one or more entry for interrupt-names property
+
+ interrupt-names:
+ $ref: /schemas/types.yaml#/definitions/string-array
+ items:
+ #The interrupt that is asserted when a wakeup event
+ #is received on USB2 bus
+ - const: hs_phy_irq
+ #The interrupt that is asserted when a wakeup event
+ #is received on USB3 bus
+ - const: ss_phy_irq
+ #Separate interrupts for any wakeup event on DM and DP lines
+ - const: dm_hs_phy_irq
+ - const: dp_hs_phy_irq
+
+ qcom,select-utmi-as-pipe-clk:
+ description:
+ if present, disable USB3 pipe_clk requirement.
+ Used when dwc3 operates without SSPHY and only
+ HS/FS/LS modes are supported.
+ type: boolean
+
+#Required child node:
+#A child node must exist to represent the core DWC3 IP block. The name of
+#the node is not important. The content of the node is defined in dwc3.txt.
+
+#Phy documentation is provided in the following places:
+#Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt - USB3 QMP PHY
+#Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt - USB2 QUSB2 PHY
+
+required:
+ - compatible
+ - reg
+ - power-domains
+ - clocks
+ - clock-names
+ - assigned-clocks
+ - assigned-clock-rates
+
+examples:
+ - |
+ hs_phy: phy@100f8800 {
+ compatible = "qcom,qusb2-v2-phy";
+ ...
+ };
+
+ ss_phy: phy@100f8830 {
+ compatible = "qcom,qmp-v3-usb3-phy";
+ ...
+ };
+
+ usb3_0: usb30@a6f8800 {
+ compatible = "qcom,dwc3";
+ reg = <0xa6f8800 0x400>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ interrupts = <0 131 0>, <0 486 0>, <0 488 0>, <0 489 0>;
+ interrupt-names = "hs_phy_irq", "ss_phy_irq",
+ "dm_hs_phy_irq", "dp_hs_phy_irq";
+
+ clocks = <&gcc GCC_USB30_PRIM_MASTER_CLK>,
+ <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_PRIM_SLEEP_CLK>;
+ clock-names = "core", "mock_utmi", "sleep";
+
+ assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_PRIM_MASTER_CLK>;
+ assigned-clock-rates = <19200000>, <133000000>;
+
+ resets = <&gcc GCC_USB30_PRIM_BCR>;
+ reset-names = "core_reset";
+ power-domains = <&gcc USB30_PRIM_GDSC>;
+ qcom,select-utmi-as-pipe-clk;
+
+ dwc3@10000000 {
+ compatible = "snps,dwc3";
+ reg = <0x10000000 0xcd00>;
+ interrupts = <0 205 0x4>;
+ phys = <&hs_phy>, <&ss_phy>;
+ phy-names = "usb2-phy", "usb3-phy";
+ dr_mode = "host";
+ };
+ };
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
\
 
 \ /
  Last update: 2019-11-28 12:40    [W:0.164 / U:0.244 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site