lkml.org 
[lkml]   [2019]   [Jan]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 10/10] arm64: dts: allwinner: h5: Add CPU Operating Performance Points table
On Wed, Jan 30, 2019 at 05:41:16PM +0800, Chen-Yu Tsai wrote:
> On Wed, Jan 30, 2019 at 5:29 PM Maxime Ripard <maxime.ripard@bootlin.com> wrote:
> >
> > On Wed, Jan 30, 2019 at 04:42:03PM +0800, Chen-Yu Tsai wrote:
> > > enable-method = "psci";
> > > clocks = <&ccu CLK_CPUX>;
> > > clock-latency-ns = <244144>; /* 8 32k periods */
> > > + operating-points-v2 = <&cpu_opp_table>;
> > > + #cooling-cells = <2>;
> > > + };
> > > + };
> > > +
> > > + cpu_opp_table: opp_table {
> > > + compatible = "operating-points-v2";
> > > + opp-shared;
> > > +
> > > + opp@408000000 {
> > > + opp-hz = /bits/ 64 <408000000>;
> > > + opp-microvolt = <1000000 1000000 1310000>;
> > > + clock-latency-ns = <244144>; /* 8 32k periods */
> > > + };
> > > +
> > > + opp@648000000 {
> > > + opp-hz = /bits/ 64 <648000000>;
> > > + opp-microvolt = <1040000 1040000 1310000>;
> > > + clock-latency-ns = <244144>; /* 8 32k periods */
> > > + };
> > > +
> > > + opp@816000000 {
> > > + opp-hz = /bits/ 64 <816000000>;
> > > + opp-microvolt = <1080000 1080000 1310000>;
> > > + clock-latency-ns = <244144>; /* 8 32k periods */
> > > + };
> > > +
> > > + opp@912000000 {
> > > + opp-hz = /bits/ 64 <912000000>;
> > > + opp-microvolt = <1120000 1120000 1310000>;
> > > + clock-latency-ns = <244144>; /* 8 32k periods */
> > > + };
> > > +
> > > + opp@960000000 {
> > > + opp-hz = /bits/ 64 <960000000>;
> > > + opp-microvolt = <1160000 1160000 1310000>;
> > > + clock-latency-ns = <244144>; /* 8 32k periods */
> > > + };
> > > +
> > > + opp@1008000000 {
> > > + opp-hz = /bits/ 64 <1008000000>;
> > > + opp-microvolt = <1200000 1200000 1310000>;
> > > + clock-latency-ns = <244144>; /* 8 32k periods */
> > > + };
> > > +
> > > + opp@1056000000 {
> > > + opp-hz = /bits/ 64 <1056000000>;
> > > + opp-microvolt = <1240000 1240000 1310000>;
> > > + clock-latency-ns = <244144>; /* 8 32k periods */
> > > + };
> > > +
> > > + opp@1104000000 {
> > > + opp-hz = /bits/ 64 <1104000000>;
> > > + opp-microvolt = <1260000 1260000 1310000>;
> > > + clock-latency-ns = <244144>; /* 8 32k periods */
> > > + };
> > > +
> > > + opp@1152000000 {
> > > + opp-hz = /bits/ 64 <1152000000>;
> > > + opp-microvolt = <1300000 1300000 1310000>;
> > > + clock-latency-ns = <244144>; /* 8 32k periods */
> >
> > What is the frequency and voltage that U-Boot sets up?
>
> 1008 MHz, and whatever voltage the board design defaults to (typically
> the higher setting).
>
> > We've had the issue with the A33 that it's started at 1008MHz, with
> > the matching voltage, and ramping up the frequency to 1.2GHz on boards
> > without PMIC support would increase the frequency but not the voltage,
> > resulting in a brownout.
>
> Which is why I added the regulator to all boards before this patch. At
> least for Linux, once the regulator supply is described in the device
> tree, if the driver is missing, regulator_get_* and thus cpufreq should
> fail with -EPROBE_DEFER.
>
> Or we could drop the extra OPPs.

Ok, if you covered all of them then fine by me. For the whole series,
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2019-01-30 11:01    [W:0.070 / U:0.352 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site