lkml.org 
[lkml]   [2019]   [Jan]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v1] clk: qcom: lpass: Add CLK_IGNORE_UNUSED for lpass clocks
From
Date


On 1/8/2019 2:34 AM, Stephen Boyd wrote:
> Quoting Taniya Das (2019-01-06 22:26:00)
>> Hello Stephen,
>>
>> On 12/21/2018 2:34 AM, Stephen Boyd wrote:
>>> Quoting Taniya Das (2018-12-20 03:46:25)
>>>> The LPASS clocks has a dependency on the GCC lpass clocks to be enabled
>>>> before accessing them and that was the reason to mark the gcc lpass clocks
>>>> as critical. But in the case where the lpass subsystem would require a
>>>> restart, toggling the lpass reset would from HW clear the SW enable bits
>>>> of the GCC lpass clocks. Thus the next time bringing up the lpass subsystem
>>>> out of reset would fail.
>>>>
>>>> Allow the lpass clock driver to enable/disable the gcc lpass clocks and
>>>> mark the lpass clocks not be accessed during late_init if no client vote.
>>>
>>> You need to add more details here. It feels like you wrote the beginning
>>> of a paragraph and then stopped abruptly, leaving the reader hanging for
>>> the whole story. Why is late_init important? Why do we need to leave
>>> them on from the bootloader? What if the bootloader doesn't leave them
>>> enabled? This is all rather hacky so I'm deeply confused. Does the lpass
>>> driver need to get these gcc clks and enable/prepare them during probe?
>>> But then it needs to also allow a reset happen and change the clk state?
>>>
>>> I suspect this situation is circling a larger problem where a reset is
>>> toggled and that changes some clk state without the clk framework
>>> knowing. There's not much we can do about that besides having some
>>> mechanism for the clks to know that their state is now out of sync. If
>>> that can be done on the provider driver side then we should have an
>>> easier time not needing to write a bunch of framework code to handle
>>> this. OMAP folks are dealing with the same problems from what I recall.
>>>
>>
>> Hmm, if I mark the CLK_IS_CRITICAL, I don't see a way to handle it in
>> provider. Please suggest if you think provider could handle it.
>
> As far as I know, I'm not suggesting the use of CLK_IS_CRITICAL here.
> But removing CLK_IS_CRITICAL and relying on some random bootloader
> behavior also looks wrong. Can you clarify what's going on?
>

To enable LPASS clocks the requirement is to enable the GCC_LPASS_SWAY
clock.
1) If the LPASS drivers are enabled/probed before the clock late init
the client would take care to maintain the dependency to enable the
GCC_LPASS_SWAY clock before enabling the LPASS clocks.

2) There could be a condition where the LPASS drivers would probe/init
later the clock late_init. When the clock_late_init would try to access
the LPASS clocks, since we cannot maintain the dependency this access
would fail. To avoid this the earlier patch has made the GCC_LPASS_SWAY
clock as CRITICAL.

3) Marking the GCC_LPASS_SWAY clock as CRITICAL has a issue, in the case
where the LPASS subsystem would be restarted due to some critical
failure on LPASS. Toggling the restart register of LPASS would clear the
hardware state of this clock and thus the next access of the LPASS
clocks would result in failure of the system.

4) To avoid issues happening in (2) and (3) all the LPASS clocks chould
be safely marked as CLK_IGNORE_UNUSED. And lpass drivers would take care
of the dependency to enable the required clocks.

Hope the above helps.

--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation.

--

\
 
 \ /
  Last update: 2019-01-14 07:13    [W:0.090 / U:0.380 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site