lkml.org 
[lkml]   [2018]   [Sep]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 3/4] PCI/portdrv: Check platform supported service IRQ's
On Fri, Aug 10, 2018 at 09:09:39PM +0530, Bharat Kumar Gogada wrote:
> Platforms may have dedicated IRQ lines for PCIe services like
> AER/PME etc., check for such IRQ lines.
> Check mask and fill legacy irq line for services other than

Capitalize "IRQ" consistently in English text like this.

Insert blank lines between paragraphs.

Add a reference to the relevant spec sections. PCIe r4.0, sec
6.2.4.1.2, 6.2.6, 7.5.3.12 seem pertinent.

> platform supported service IRQ number.
>
> Signed-off-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
> ---
> drivers/pci/pcie/portdrv_core.c | 19 +++++++++++++++++--
> 1 files changed, 17 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/pci/pcie/portdrv_core.c b/drivers/pci/pcie/portdrv_core.c
> index e0261ad..a7d024c 100644
> --- a/drivers/pci/pcie/portdrv_core.c
> +++ b/drivers/pci/pcie/portdrv_core.c
> @@ -166,6 +166,19 @@ static int pcie_init_service_irqs(struct pci_dev *dev, int *irqs, int mask)
> irqs[i] = -1;
>
> /*
> + * Some platforms have dedicated interrupt line from root complex to
> + * interrupt controller for PCIe services like AER/PME etc., check
> + * if platform registered with any such IRQ.
> + */
> + if (pci_pcie_type(dev) == PCI_EXP_TYPE_ROOT_PORT) {
> + int plat_mask;
> +
> + plat_mask = pci_check_platform_service_irqs(dev, irqs, mask);
> + if (plat_mask > 0)

Masks should be unsigned and tested for zero or "mask & bit". The
rest of this file uses "int", which is sloppy because it does the
wrong thing if we happen to use the high-order bit in the mask.

> + mask = mask & plat_mask;
> + }

I think these platform IRQs are neither MSI-X/MSI nor PCI INTx wires.
But as written, I think this patch executes pcie_port_enable_irq_vec(),
which only does MSI-X/MSI stuff. So this must rely on that failing?

And then we fall through to run pci_alloc_irq_vectors(), which is for
PCI INTx interrupts, which doesn't seem appropriate either.

It seems like this platform IRQ case should be completely separated
from the other MSI/INTx cases, i.e., set
irqs[PCIE_PORT_SERVICE_AER_SHIFT] directly (I think you already do
this inside pci_check_platform_service_irqs()) and immediately return.
Then I think you wouldn't need the other hunk below.

> +
> + /*
> * If we support PME but can't use MSI/MSI-X for it, we have to
> * fall back to INTx or other interrupts, e.g., a system shared
> * interrupt.
> @@ -183,8 +196,10 @@ static int pcie_init_service_irqs(struct pci_dev *dev, int *irqs, int mask)
> if (ret < 0)
> return -ENODEV;
>
> - for (i = 0; i < PCIE_PORT_DEVICE_MAXSERVICES; i++)
> - irqs[i] = pci_irq_vector(dev, 0);
> + for (i = 0; i < PCIE_PORT_DEVICE_MAXSERVICES; i++) {
> + if (mask & (1 << i))
> + irqs[i] = pci_irq_vector(dev, 0);
> + }
>
> return 0;
> }
> --
> 1.7.1
>

\
 
 \ /
  Last update: 2018-09-04 16:13    [W:0.165 / U:1.164 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site