lkml.org 
[lkml]   [2018]   [Sep]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v3 6/9] kbuild: consolidate Devicetree dtb build rules
2018-09-13 11:51 GMT-04:00 Geert Uytterhoeven <geert@linux-m68k.org>:
> Hi Yamada-san,
>
> On Wed, Sep 12, 2018 at 3:02 AM Masahiro Yamada
> <yamada.masahiro@socionext.com> wrote:
>> 2018-09-12 0:40 GMT+09:00 Rob Herring <robh@kernel.org>:
>> > On Mon, Sep 10, 2018 at 10:04 AM Rob Herring <robh@kernel.org> wrote:
>> >> There is nothing arch specific about building dtb files other than their
>> >> location under /arch/*/boot/dts/. Keeping each arch aligned is a pain.
>> >> The dependencies and supported targets are all slightly different.
>> >> Also, a cross-compiler for each arch is needed, but really the host
>> >> compiler preprocessor is perfectly fine for building dtbs. Move the
>> >> build rules to a common location and remove the arch specific ones. This
>> >> is done in a single step to avoid warnings about overriding rules.
>> >>
>> >> The build dependencies had been a mixture of 'scripts' and/or 'prepare'.
>> >> These pull in several dependencies some of which need a target compiler
>> >> (specifically devicetable-offsets.h) and aren't needed to build dtbs.
>> >> All that is really needed is dtc, so adjust the dependencies to only be
>> >> dtc.
>> >>
>> >> This change enables support 'dtbs_install' on some arches which were
>> >> missing the target.
>> >
>> > [...]
>> >
>> >> @@ -1215,6 +1215,33 @@ kselftest-merge:
>> >> $(srctree)/tools/testing/selftests/*/config
>> >> +$(Q)$(MAKE) -f $(srctree)/Makefile olddefconfig
>> >>
>> >> +# ---------------------------------------------------------------------------
>> >> +# Devicetree files
>> >> +
>> >> +ifneq ($(wildcard $(srctree)/arch/$(SRCARCH)/boot/dts/),)
>> >> +dtstree := arch/$(SRCARCH)/boot/dts
>> >> +endif
>> >> +
>> >> +ifdef CONFIG_OF_EARLY_FLATTREE
>> >
>> > This can be true when dtstree is unset. So this line should be this
>> > instead to fix the 0-day reported error:
>> >
>> > ifneq ($(dtstree),)
>> >
>> >> +
>> >> +%.dtb : scripts_dtc
>> >> + $(Q)$(MAKE) $(build)=$(dtstree) $(dtstree)/$@
>> >> +
>> >> +PHONY += dtbs dtbs_install
>> >> +dtbs: scripts_dtc
>> >> + $(Q)$(MAKE) $(build)=$(dtstree)
>> >> +
>> >> +dtbs_install: dtbs
>> >> + $(Q)$(MAKE) $(dtbinst)=$(dtstree)
>> >> +
>> >> +all: dtbs
>> >> +
>> >> +endif
>>
>>
>> Ah, right.
>> Even x86 can enable OF and OF_UNITTEST.
>>
>>
>>
>> Another solution might be,
>> guard it by 'depends on ARCH_SUPPORTS_OF'.
>>
>>
>>
>> This is actually what ACPI does.
>>
>> menuconfig ACPI
>> bool "ACPI (Advanced Configuration and Power Interface) Support"
>> depends on ARCH_SUPPORTS_ACPI
>> ...
>
> ACPI is a real platform feature, as it depends on firmware.
>
> CONFIG_OF can be enabled, and DT overlays can be loaded, on any platform,
> even if it has ACPI ;-)
>

OK, understood.

Thanks!



--
Best Regards
Masahiro Yamada

\
 
 \ /
  Last update: 2018-09-23 12:33    [W:0.091 / U:0.848 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site