lkml.org 
[lkml]   [2018]   [Sep]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v3 2/3] spis: mediatek: add spi slave for Mediatek MT2712
From
Date
Hi Mark,
Thanks for your comments.

On Tue, 2018-09-18 at 09:30 -0700, Mark Brown wrote:
> On Mon, Sep 17, 2018 at 10:19:21AM +0800, Leilk Liu wrote:
>
> This looks overall pretty good, a few smallish comments below:
>
> Please use subject lines matching the style for the subsystem. This
> makes it easier for people to identify relevant patches.
>
OK, I'll fix it, thanks.

> > if SPI_SLAVE
> > +config SPI_SLAVE_MT27XX
> > + tristate "MediaTek SPI slave device"
> > + depends on ARCH_MEDIATEK || COMPILE_TEST
> > + help
> > + This selects the MediaTek(R) SPI slave device driver.
> > + If you want to use MediaTek(R) SPI slave interface,
> > + say Y or M here.If you are not sure, say N.
> > + SPI slave drivers for Mediatek MT27XX series ARM SoCs.
> >
> > config SPI_SLAVE_TIME
>
> This is a driver not a slave implementation, it should be with the other
> drivers in the Kconfig. The slave implementations are for the
> functionality that uses the drivers, not the drivers themselves.
>
OK, I'll fix it, thanks.

> > + /* set the tx/rx endian */
> > +#ifdef __LITTLE_ENDIAN
> > + reg_val &= ~SPIS_TX_ENDIAN;
> > + reg_val &= ~SPIS_RX_ENDIAN;
> > +#else
> > + reg_val |= SPIS_TX_ENDIAN;
> > + reg_val |= SPIS_RX_ENDIAN;
> > +#endif
> > + writel(reg_val, mdata->base + SPIS_CFG_REG);
>
> This seems weird - it looks like it's changing the endianess of the
> protocol based on the endianness the processor is running in. What's
> going on here? I'd expect the driver to be just treating everything as
> a byte stream and letting the protocol driver handle the endianness
> issues, otherwise we might end up with double converions.
>
OK, I'll set the endian of SPI the same with the processor. Thanks.

> > + xfer->tx_dma = dma_map_single(dev, (void *)xfer->tx_buf,
> > + xfer->len, DMA_TO_DEVICE);
>
> Why is there a cast to void here? That's usually a sign that there's a
> type safety issue, the whole point with void is that it's compatible
> with any other pointer.
>
tx_buf is a const void*, here it need a void * for the dma mapping.
And I'll remove void * from dma_map_single((void *)rx_buf).
Thanks.

> > +static irqreturn_t mtk_spi_slave_interrupt(int irq, void *dev_id)
> > +{
> > + struct spi_controller *ctlr = dev_id;
> > + struct mtk_spi_slave *mdata = spi_controller_get_devdata(ctlr);
> > + struct spi_transfer *trans = mdata->cur_transfer;
> > + u32 int_status, reg_val, cnt, remainder;
> > +
> > + int_status = readl(mdata->base + SPIS_IRQ_ST_REG);
> > + writel(int_status, mdata->base + SPIS_IRQ_CLR_REG);
> > +
> > + if (!trans)
> > + return IRQ_HANDLED;
>
> Are you sure that this is the right thing to do if we get a spurious
> interrupt - the normal thing would be to return IRQ_NONE, possibly
> logging a warning as well?
>
OK, it should reture IRQ_NONE here, thanks.

> > + if (int_status & CMD_INVALID_ST)
> > + dev_err(&ctlr->dev, "cmd invalid\n");
>
> If there's an interrupt that doesn't have any of the interrupt status
> flags set I'd expect to see a warning and probably IRQ_NONE being
> returned. That way if the interrupt line is shared we work correctly
> and if something goes wrong and the interrupt gets stuck on then the
> core interrupt code's error handling can kick in.
OK, I'll fix it, thanks.


\
 
 \ /
  Last update: 2018-09-19 07:50    [W:0.070 / U:1.132 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site