lkml.org 
[lkml]   [2018]   [Sep]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 1/2] dt-binding: mediatek: Add binding document for MediaTek GMAC
From
Date
On Mon, 2018-09-17 at 11:33 +0300, Sergei Shtylyov wrote:
> On 9/17/2018 9:29 AM, Biao Huang wrote:
>
> > The commit adds the device tree binding documentation for the MediaTek
> > GMAC found on Mediatek MT2712.
> >
> > Signed-off-by: Biao Huang <biao.huang@mediatek.com>
> > ---
> > .../devicetree/bindings/net/mediatek-gmac.txt | 45 ++++++++++++++++++++
> > 1 file changed, 45 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/net/mediatek-gmac.txt
> >
> > diff --git a/Documentation/devicetree/bindings/net/mediatek-gmac.txt b/Documentation/devicetree/bindings/net/mediatek-gmac.txt
> > new file mode 100644
> > index 0000000..14876ed
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/net/mediatek-gmac.txt
> > @@ -0,0 +1,45 @@
> > +MediaTek Gigabit Ethernet controller
> > +=========================================
> > +
> > +The gigabit ethernet controller can be found on MediaTek SoCs.
> > +
> > +* Ethernet controller node
> > +
> > +Required properties:
> > +- compatible: Should be
> > + "mediatek,mt2712-eth": for MT2712 SoC
> > +- reg: Address and length of the register set for the device
> > +- interrupts: Should contain the MAC interrupts
> > +- interrupt-names: the name of interrupt in the interrupts property. These are
> > + "macirq": For MT2712 SoC
> > +- clocks: the clock used by the controller
> > +- clock-names: the names of the clock listed in the clocks property. These are
> > + "axi", "apb", "mac_ext", "ptp", "ptp_parent", "ptp_top": For MT2712 SoC
> > +- mac-address: See ethernet.txt in the same directory
> > +- power-domains: phandle to the power domain that the ethernet is part of
>
> This (required) prop is absent in your example.
thanks for your comments, power-domains is not a required property, and
I'll modify this property in next version.
>
> > +- phy-mode: See ethernet.txt file in the same directory.
> > +- reset-gpio: gpio number for phy reset.
> > +
> > +Example:
> > +
> > +eth: eth@1101c000 {
>
> eth: ethernet@1101c000 {
>
> > + compatible = "mediatek,mt2712-eth";
> > + reg = <0 0x1101c000 0 0x1200>;
> > + interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>;
> > + interrupt-names = "macirq";
> > + phy-mode ="rgmii";
> > + mac-address = [00 55 7b b5 7d f7];
> > + clock-names = "axi",
> > + "apb",
> > + "mac_ext",
> > + "ptp",
> > + "ptp_parent",
> > + "ptp_top";
> > + clocks = <&pericfg CLK_PERI_GMAC>,
> > + <&pericfg CLK_PERI_GMAC_PCLK>,
> > + <&topckgen CLK_TOP_ETHER_125M_SEL>,
> > + <&topckgen CLK_TOP_ETHER_50M_SEL>,
> > + <&topckgen CLK_TOP_APLL1_D3>,
> > + <&topckgen CLK_TOP_APLL1>;
> > + reset-gpio = <&pio 87 GPIO_ACTIVE_HIGH>;
> > + };
>
> MBR, Sergei
Best Regards!
Biao


\
 
 \ /
  Last update: 2018-09-18 03:14    [W:0.697 / U:0.320 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site