lkml.org 
[lkml]   [2018]   [Sep]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 1/2] sc16is7xx: Fix for multi-channel stall
On Tue, Sep 18, 2018 at 02:13:15PM +0100, Phil Elwell wrote:
> Hi Greg,
>
> On 18/09/2018 14:02, Greg Kroah-Hartman wrote:
> > On Wed, Sep 12, 2018 at 03:31:55PM +0100, Phil Elwell wrote:
> >> The SC16IS752 is a dual-channel device. The two channels are largely
> >> independent, but the IRQ signals are wired together as an open-drain,
> >> active low signal which will be driven low while either of the
> >> channels requires attention, which can be for significant periods of
> >> time until operations complete and the interrupt can be acknowledged.
> >> In that respect it is should be treated as a true level-sensitive IRQ.
> >>
> >> The kernel, however, needs to be able to exit interrupt context in
> >> order to use I2C or SPI to access the device registers (which may
> >> involve sleeping). Therefore the interrupt needs to be masked out or
> >> paused in some way.
> >>
> >> The usual way to manage sleeping from within an interrupt handler
> >> is to use a threaded interrupt handler - a regular interrupt routine
> >> does the minimum amount of work needed to triage the interrupt before
> >> waking the interrupt service thread. If the threaded IRQ is marked as
> >> IRQF_ONESHOT the kernel will automatically mask out the interrupt
> >> until the thread runs to completion. The sc16is7xx driver used to
> >> use a threaded IRQ, but a patch switched to using a kthread_worker
> >> in order to set realtime priorities on the handler thread and for
> >> other optimisations. The end result is non-threaded IRQ that
> >> schedules some work then returns IRQ_HANDLED, making the kernel
> >> think that all IRQ processing has completed.
> >>
> >> The work-around to prevent a constant stream of interrupts is to
> >> mark the interrupt as edge-sensitive rather than level-sensitive,
> >> but interpreting an active-low source as a falling-edge source
> >> requires care to prevent a total cessation of interrupts. Whereas
> >> an edge-triggering source will generate a new edge for every interrupt
> >> condition a level-triggering source will keep the signal at the
> >> interrupting level until it no longer requires attention; in other
> >> words, the host won't see another edge until all interrupt conditions
> >> are cleared. It is therefore vital that the interrupt handler does not
> >> exit with an outstanding interrupt condition, otherwise the kernel
> >> will not receive another interrupt unless some other operation causes
> >> the interrupt state on the device to be cleared.
> >>
> >> The existing sc16is7xx driver has a very simple interrupt "thread"
> >> (kthread_work job) that processes interrupts on each channel in turn
> >> until there are no more. If both channels are active and the first
> >> channel starts interrupting while the handler for the second channel
> >> is running then it will not be detected and an IRQ stall ensues. This
> >> could be handled easily if there was a shared IRQ status register, or
> >> a convenient way to determine if the IRQ had been deasserted for any
> >> length of time, but both appear to be lacking.
> >>
> >> Avoid this problem (or at least make it much less likely to happen)
> >> by reducing the granularity of per-channel interrupt processing
> >> to one condition per iteration, only exiting the overall loop when
> >> both channels are no longer interrupting.
> >>
> >> Signed-off-by: Phil Elwell <phil@raspberrypi.org>
> >> ---
> >> drivers/tty/serial/sc16is7xx.c | 19 +++++++++++++------
> >> 1 file changed, 13 insertions(+), 6 deletions(-)
> >>
> >> diff --git a/drivers/tty/serial/sc16is7xx.c b/drivers/tty/serial/sc16is7xx.c
> >> index 243c960..47b4115 100644
> >> --- a/drivers/tty/serial/sc16is7xx.c
> >> +++ b/drivers/tty/serial/sc16is7xx.c
> >> @@ -657,7 +657,7 @@ static void sc16is7xx_handle_tx(struct uart_port *port)
> >> uart_write_wakeup(port);
> >> }
> >>
> >> -static void sc16is7xx_port_irq(struct sc16is7xx_port *s, int portno)
> >> +static bool sc16is7xx_port_irq(struct sc16is7xx_port *s, int portno)
> >> {
> >> struct uart_port *port = &s->p[portno].port;
> >>
> >> @@ -666,7 +666,7 @@ static void sc16is7xx_port_irq(struct sc16is7xx_port *s, int portno)
> >>
> >> iir = sc16is7xx_port_read(port, SC16IS7XX_IIR_REG);
> >> if (iir & SC16IS7XX_IIR_NO_INT_BIT)
> >> - break;
> >> + return false;
> >>
> >> iir &= SC16IS7XX_IIR_ID_MASK;
> >>
> >> @@ -688,16 +688,23 @@ static void sc16is7xx_port_irq(struct sc16is7xx_port *s, int portno)
> >> port->line, iir);
> >> break;
> >> }
> >> - } while (1);
> >> + } while (0);
> >> + return true;
> >> }
> >>
> >> static void sc16is7xx_ist(struct kthread_work *ws)
> >> {
> >> struct sc16is7xx_port *s = to_sc16is7xx_port(ws, irq_work);
> >> - int i;
> >>
> >> - for (i = 0; i < s->devtype->nr_uart; ++i)
> >> - sc16is7xx_port_irq(s, i);
> >> + while (1) {
> >> + bool keep_polling = false;
> >> + int i;
> >> +
> >> + for (i = 0; i < s->devtype->nr_uart; ++i)
> >> + keep_polling |= sc16is7xx_port_irq(s, i);
> >> + if (!keep_polling)
> >> + break;
> >
> > This makes me worried, there is no "timeout" now? What happens if this
> > never happens, will you just sit and spin forever? What prevents that?
>
> The patch is keeping to the spirit of the original, which also has a
> potentially infinite loop (in sc16is7xx_port_irq) - this just moves it
> up one level.
>
> I could add a limit on the number of iterations, but if the limit is ever hit,
> leading to an early exit, the port is basically dead because it will never
> receive another interrupt.

Ok, it's your hardware, good luck with it! :)

greg k-h

\
 
 \ /
  Last update: 2018-09-18 15:27    [W:0.098 / U:1.616 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site