lkml.org 
[lkml]   [2018]   [Sep]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH v3 3/3] dt-bindings: mfd: max8998: Add charger subnode binding
Date
On Tuesday, August 7, 2018 11:57:42 AM CEST Rob Herring wrote:
> On Tue, Jul 17, 2018 at 06:05:09PM +0200, Paweł Chmiel wrote:
> > This patch adds devicetree bindings documentation for
> > battery charging controller as the subnode of MAX8998 PMIC.
> >
> > Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
> > ---
> > Changes from v2:
> > - Make charge-restart-level-microvolt optional.
> > - Make charge-timeout-hours optional.
> >
> > Changes from v1:
> > - Removed unneeded Fixes tag
> > - Correct description of all charger values
> > - Added missing property unit
> > ---
> > Documentation/devicetree/bindings/mfd/max8998.txt | 25 +++++++++++++++++++++++
> > 1 file changed, 25 insertions(+)
> >
> > diff --git a/Documentation/devicetree/bindings/mfd/max8998.txt b/Documentation/devicetree/bindings/mfd/max8998.txt
> > index 23a3650ff2a2..264040f4ad15 100644
> > --- a/Documentation/devicetree/bindings/mfd/max8998.txt
> > +++ b/Documentation/devicetree/bindings/mfd/max8998.txt
> > @@ -50,6 +50,24 @@ Additional properties required if max8998,pmic-buck2-dvs-gpio is defined:
> > - max8998,pmic-buck2-dvs-voltage: An array of 2 voltage values in microvolts
> > for buck2 regulator that can be selected using dvs gpio.
> >
> > +Charger: Configuration for battery charging controller should be added
> > +inside a child node named 'charger'.
> > + Required properties:
> > + - max8998,charge-eoc-percent: Setup End of Charge Level.
>
> This should have a vendor prefix and max8998 is not a vendor. Don't
> continue that pattern even if we already have some properties like that.
>
> These seem like perhaps they should be common charger properties.
Where i could find such properties (or any other driver which is using those as an example) ?
Looking at few existing drivers, most of them have custom properties (that's why i've followed the same pattern for max8998).

Thanks
>
> > + If value equals 0, leave it unchanged.
> > + Otherwise it should be value from 10 to 45 by 5 step.
> > +
> > + Optional properties:
> > + - max8998,charge-restart-level-microvolt: Setup Charge Restart Level.
> > + If property is not present, this will be disabled.
> > + If value equals 0, leave it unchanged.
> > + Otherwise it should be one of following values: 100, 150, 200.
> > +
> > + - max8998,charge-timeout-hours: Setup Charge Full Timeout.
> > + If property is not present, this will be disabled.
> > + If value equals 0, leave it unchanged.
> > + Otherwise it should be one of following values: 5, 6, 7.
> > +
> > Regulators: All the regulators of MAX8998 to be instantiated shall be
> > listed in a child node named 'regulators'. Each regulator is represented
> > by a child node of the 'regulators' node.
> > @@ -99,6 +117,13 @@ Example:
> > max8998,pmic-buck2-dvs-gpio = <&gpx0 0 3 0 0>; /* SET3 */
> > max8998,pmic-buck2-dvs-voltage = <1350000>, <1300000>;
> >
> > + /* Charger configuration */
> > + charger {
> > + max8998,charge-eoc-percent = <0>;
> > + max8998,charge-restart-level-microvolt = <100>;
> > + max8998,charge-timeout-hours = <7>;
> > + };
> > +
> > /* Regulators to instantiate */
> > regulators {
> > ldo2_reg: LDO2 {
>


\
 
 \ /
  Last update: 2018-09-13 16:55    [W:0.099 / U:0.996 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site