lkml.org 
[lkml]   [2018]   [Sep]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 2/2] dmaengine: uniphier-mdmac: add UniPhier MIO DMAC driver
On 12-09-18, 14:25, Masahiro Yamada wrote:
> 2018-09-12 13:35 GMT+09:00 Vinod <vkoul@kernel.org>:
> > On 12-09-18, 12:01, Masahiro Yamada wrote:
> >> Hi Vinod,
> >>
> >>
> >> 2018-09-11 16:00 GMT+09:00 Vinod <vkoul@kernel.org>:
> >> > On 24-08-18, 10:41, Masahiro Yamada wrote:
> >> >
> >> >> +/* mc->vc.lock must be held by caller */
> >> >> +static u32 __uniphier_mdmac_get_residue(struct uniphier_mdmac_desc *md)
> >> >> +{
> >> >> + u32 residue = 0;
> >> >> + int i;
> >> >> +
> >> >> + for (i = md->sg_cur; i < md->sg_len; i++)
> >> >> + residue += sg_dma_len(&md->sgl[i]);
> >> >
> >> > so if the descriptor is submitted to hardware, we return the descriptor
> >> > length, which is not correct.
> >> >
> >> > Two cases are required to be handled:
> >> > 1. Descriptor is in queue (IMO above logic is fine for that, but it can
> >> > be calculated at descriptor submit and looked up here)
> >>
> >> Where do you want it to be calculated?
> >
> > where is it calculated now?
>
>
> Please see __uniphier_mdmac_handle().
>
>
> It gets the address and size by sg_dma_address(), sg_dma_len()
> just before setting them to the hardware registers.
>
>
> sg = &md->sgl[md->sg_cur];
>
> if (md->dir == DMA_MEM_TO_DEV) {
> src_mode = UNIPHIER_MDMAC_CH_MODE__ADDR_INC;
> src_addr = sg_dma_address(sg);
> dest_mode = UNIPHIER_MDMAC_CH_MODE__ADDR_FIXED;
> dest_addr = 0;
> } else {
> src_mode = UNIPHIER_MDMAC_CH_MODE__ADDR_FIXED;
> src_addr = 0;
> dest_mode = UNIPHIER_MDMAC_CH_MODE__ADDR_INC;
> dest_addr = sg_dma_address(sg);
> }
>
>
>
>
>
>
>
> >> This hardware provides only simple registers (address and size)
> >> for one-shot transfer instead of descriptors.
> >>
> >> So, I used sgl as-is because I did not see a good reason
> >> to transform sgl to another data structure.
> >
> >
> >> > this seems missing stuff. Where do you do register calculation for the
> >> > descriptor and where is slave_config here, how do you know where to
> >> > send/receive data form/to (peripheral)
> >>
> >>
> >> This dmac is really simple, and un-flexible.
> >>
> >> The peripheral address to send/receive data from/to is hard-weird.
> >> cfg->{src_addr,dst_addr} is not configurable.
> >>
> >> Look at __uniphier_mdmac_handle().
> >> 'dest_addr' and 'src_addr' must be set to 0 for the peripheral.
> >
> > Fair enough, what about other values like addr_width and maxburst?
>
>
> None of them is configurable.

what is configurable here :-)

Who are the users of this DMA?

--
~Vinod

\
 
 \ /
  Last update: 2018-09-12 09:28    [W:0.054 / U:0.324 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site